HNP Mikrosysteme mzr-11507 Скачать руководство пользователя

Страница: 7 / 55

1 General Information

Operating manual mzr-11507

Last update: August 2016

Technical data subject to change without prior notice!.

1.3

Technical data of the micro annular gear pump mzr-11507

The following table shows the technical data of the micro annular gear pump

head

mzr

-11507.

Constructive Specifications

Measurements (L x W x H)

303 x 110 x 171 mm

Weight

approx. 9,3 kg

Material case

stainless steel 1.4404, 1.4435 (316L)

Material rotor

tungsten carbide Ni-based

Material bearing

tungsten carbide Ni-based

Shaft seal

graphite reinforced Teflon

, 316L

Static seals

FPM (Viton

), optional: EPDM, FFPM

Fluid connections

3/8" NPT internal thread, lateral

Tubes D / ID

6 / 4 mm

Technical data

Flow rate

29 – 1152 ml/min ( = 69,1 l/h)

Smallest dosage volume

100 µl

Displacement volume

192 µl

Operating pressure range

0 – 40 bar (by Viskosity 1 mPas)

0 – 140 bar (by Viskosity 16 mPas)

Max. inlet pressure

10 bar

Viscosity range

0.3 – 150,000 mPas

Precision

< 1 % Coefficient of Variation CV

Pulsation

< 6 %

Internal volume

8506 µl

Operating temperature range

-5 … +60 °C (-20 … +120 °C *)

Ambient temperature range

-20 … +40 °C

Store temperature range

-5 … +40 °C

caption: * Differing specifications on request

table 1

Technical data of the micro annular gear pump head mzr-11507

Warning

The material properties of a liquid (e.g. viscosity, lubricating property, particle

content, corrosiveness) impacts the technical data and the lifetime of pumps.

Under appropriate conditions the characteristic values may be increased or

decreased.

Warning

If you intend to operate the pump out of the range of the above given

specification, please consult the manufacturer. Modifications may be necessary

to ensure successful operation. Otherwise the pump or the system may be

damaged seriously.

Содержание mzr-11507
























































Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-11507, Руководство по эксплуатации

Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды