HNP Mikrosysteme mzr-11507 Скачать руководство пользователя

Страница: 25 / 55

5 Optional modules

Operating manual mzr-11507

Last update: August 2016

Technical data subject to change without prior notice!.

5.4

Heating device „

JET

micro“

The heating device „

JET

micro“ has been designed for use with the electric

heating module (see chapter 5.3.1).

Hand:

Blinks during temperature set in the manual input mode

Ada:

Ada display blinks during the automatic control adjustment

AL:

Alarm display – not configured, no importance

Actual value

display:

= sensor failure

= sensor reverse polarity

With or the nominal temperature may be set.

Power supply

Shock-proof plug, 3 m long, 90-230 VAC

Electrical connection

10-pole bush insert, 16 A/250 V

Heating

Sensor

Zone 1

Zone 2 (Option)

table 7

Pin configuration of the heating device

No importance

Actual value

Nominal value

No importance

Heating on

Increase the temperature

No importance

Decrease the temperature

Содержание mzr-11507
























































Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-11507, Руководство по эксплуатации

Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды