HMS Anybus Edge Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 150

background image

92 (148)

TCP settings

Port

TCP port number the Modbus TCP server will be listening on - typically 502. Note that the unit ID is
not evaluated in TCP server mode.

Keep-alive
enable

Enables the TCP keep-alive mechanism for connections from clients. The keep-alive mechanism is
used to detect dead connections. When a dead connection is detected, resources consumed by this
connection can be released.

Keep-alive
timeout

Idle time in seconds after which the first keep-alive probe will be sent

Keep-alive
interval

Interval in seconds in which keep-alive probes will be sent

Keep-alive count

Number of keep-alive probes that will be sent before closing the connection

RTU settings

Interface

Serial interface the Modbus RTU Slave should run on. This selection is only available if your Edge
gateway device features more than one serial interface.

Address

RTU slave's address

RTU mode

Defines the mode for Modbus RTU. There are three possible options:

•

RS232 with RTS/CTS flow control

•

RS232 without flow control

•

RS485

Baud rate

Defines the baud rate for Modbus RTU

Parity

Defines the parity (and stop bits) for Modbus RTU. There are three possible options:

•

None (2 stop bits)

•

Odd

•

Even

Event Log Messages

The following section describes the messages that the Modbus Slave driver may log to the Event
Log. All Messages are prefixed with the text

Modbus Slv driver:

.

•

Portal communication error

<error code>

A general error has occurred while exchanging data with the portal. Possible error codes:

-2

Out of memory

-3

The internal data queue has overflown, because data was produced faster than it could be processed.

If you see an error code that is not on the above list, please contact the customer support.

M-Bus

If your Edge gateway device features an M-Bus interface, you can configure it via this form.

At the top of the page you can configure several settings.

Baud rate

Baud rate at which the M-Bus will operate.

Addressing
mode

Mode used to address the M-Bus slave devices (Primary, secondary or reverse secondary).

Append new
devices to
the list

When this option is set, the scan results are appended to the saved List.

Maximum
number of
pages per
device

Via this option you can limit the number of pages to be requested from each device. Typically the first
page contains the most important values.

Maximum
number of

Via this option you can limit the number of values to be read from each device. Note that the total
number of values read from all devices is limited to 4096 and that at least one value will be read from
any device. The number of devices to be read is limited to 64.

Anybus Edge Gateway Reference Guide

SCM-1202-154 1.0 en-US

«
...
92
93
94
95
96
...
»

Содержание Anybus Edge























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Anybus Edge

Бренд: Karel Страницы: 17

Бренд: Yes Страницы: 2

Nmea Connect Plus

Бренд: Calypso Страницы: 21

Бренд: VBOX Страницы: 90

Бренд: Top Global Страницы: 75

easyconnect ec350

Бренд: Netbiter Страницы: 40

Air Live SG-101

Бренд: Ovislink Страницы: 18

Бренд: ZyXEL Communications Страницы: 323

Бренд: Ubee Страницы: 7

Бренд: Sharp Страницы: 16

Бренд: Zoom Страницы: 2

Бренд: ioLIVING Страницы: 3

AirPoint 2011-BYMG

Бренд: Arrive Страницы: 2

Fieldgate FXA720

Бренд: Endress+Hauser Страницы: 66

Бренд: 2Wire Страницы: 82

Бренд: ELKOR Страницы: 2

Бренд: Watchguard Страницы: 26

Бренд: BellEquip Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды