Hiwin RA605-710-GC Скачать руководство пользователя страница 9

Страница: 9 / 70

C22UE001-2004



Do not pull the connector violently or twist the
electric wires excessively.



Do not frequently switch ON/OFF the power
switch and the control button.



Please ensure that the robot, the emergency stop
switch and the controller are functioning properly
before performing any work.



Do not shutdown the power switch during the
operation.



Do not open, modify, disassemble and maintain the
machine without permission.



The power must be disconnected when the machine
does not operate in a long time.



Do not turn off the power of the controller when
modifying the program or parameter. Otherwise, the
data stored in the controller will be damaged.



After the brake of a servo motor is released, the
robot will be moved due to gravity and it may
injured the operator.



The industrial robots can be applied for the different
industrial environments.



When the operating procedures are interrupted, the
special attention should be paid during the
troubleshooting.

Содержание RA605-710-GC







































































Результаты поиска

Содержание RA605-710-GC

Отзывы:

Похожие инструкции для RA605-710-GC

Бренды по названию

Популярные бренды

Hiwin RA605-710-GC, Руководство пользователя

Результаты поиска

Содержание RA605-710-GC

Отзывы:

Похожие инструкции для RA605-710-GC

Бренды по названию

Популярные бренды