Hiwin RA605-710-GC Скачать руководство пользователя страница 59

Страница: 59 / 70

C22UE001-2004

Figure 6-1 The backup batteries replacement

6.2.2 Timing Belt Replacement

The timing belt is used in the robot for the driver system of the J2, J3, J5 and J6 -axis. Although

the belt tension has been adjusted before the robot delivery, the timing belt will wear depending on

the working conditions. The belt tension might be lower than the standard after operating for a long

time. The timing belt should be periodically checked, maintained and replaced.



Timing Belt replacement period

When the maintenance time is up to (six month), check the belt tension. If the tension is

insufficient, adjust the belt tension. If the belt is excessively worn (wearing about half of the tooth

width), the belt tooth is cracked or the belt is broken, replace the belt, but you are required to re-origin

the points to correct the points.



When replacing the belt, the robot system origin may deviate.

In this case, the position data must be rechecked if the origin

is offset. Please refer to section 4.1 for Zero-position setting.

Cover screw

Battery cover

Rubber seal

Содержание RA605-710-GC







































































Результаты поиска

Содержание RA605-710-GC

Отзывы:

Похожие инструкции для RA605-710-GC

Бренды по названию

Популярные бренды

Hiwin RA605-710-GC, Руководство пользователя

Результаты поиска

Содержание RA605-710-GC

Отзывы:

Похожие инструкции для RA605-710-GC

Бренды по названию

Популярные бренды