Hiwin RA605-710-GC Скачать руководство пользователя страница 65

Страница: 65 / 70

C22UE001-2004



Inspect J5-axis timing belt

Step1.

Ensure the power of controller is switched off.

Step2.

Remove the cover of J5.

Step3.

Check whether the timing belt is normal.

Step4.

If the timing belt is abnormal, refer to the following paragraph to replace the
timing belt.

Step5.

If the belt tension is lower than the standard, refer to the following paragraph to
adjust the belt tension.



Adjust J5-axis timing belt

Step1.

Loose the two fixing screws on motor flange, so that the motor can be move.
No need to remove the screws.

Step2.

Refer to Table 6-4, loosen or tighten the adjusting screw to adjust the tension of
the belt.

Step3.

Tighten the two fixing screws on motor flange. (Screw pounds 2.2N-m)



Replace J5-axis timing belt

Step1.

Remove the two fixing screws on motor plate.

Step2.

Loose the adjusting screw to replace the timing belt.

Step3.

After replacing the belt, refer to the paragraph “Adjust J5-axis timing belt”
above to adjust the tension of the belt.



Inspection, maintenance and replacement of timing belt in J6-axis.

Figure 6-7 shows the structure of J6-axis.

Figure 6-7 J6-axis structure diagram

Belt pulley

Belt

Belt pulley

Tension adjusting screw

Screws for motor flange

Содержание RA605-710-GC







































































Результаты поиска

Содержание RA605-710-GC

Отзывы:

Похожие инструкции для RA605-710-GC

Бренды по названию

Популярные бренды

Hiwin RA605-710-GC, Руководство пользователя

Результаты поиска

Содержание RA605-710-GC

Отзывы:

Похожие инструкции для RA605-710-GC

Бренды по названию

Популярные бренды