Hitachi SJ-DN2 Скачать руководство пользователя страница 5

Страница: 5 / 55

CHAPTER 1 INTRODUCTION

1.1 INSPECTION UPON UNPACKING

Make sure to treat the product carefully not to give shock and vibration while unpacking. Check that the

product is the one you ordered, no defect, and that there is no damage during transportation.

(Contents of packing)

(1) SJ-DN2(DeviceNet option printed board): 1

(2) Instruction manual: 1

(3) DeviceNet connector: 1

(4) Screws fixed printed board (M3 times 8 mm): 2

If you discover any problem, contact your sales agent immediately.

1.2 INQUIRY OF THE PRODUCT AND WARRANTY FOR THE PRODUCT

1.2.1 REQUIRE WHILE INQUIRING

If inquiry of breakage, question, damage etc. is needed, please tell the following information to the supplier

you ordered or the nearest Hitachi Distributor.

(1) Type(SJ-DN2)

(2) Manufacturing number (Item of label, that labeled surface of printed board. SJ-DN2 XXX )

(3) Date of purchasing

(4) Contents of inquiry

・

Damage parts and its condition etc.

・

Question parts and their contents etc.

In order to shorten impossible working time, standing spare unit is recommended.

1.2.2 WARRANTY OF THE PRODUCT

This product is guaranteed to last for one year after purchase. But, the next case is toll repair, even if within

warranty period.

(1) In case caused by operating mistake, and incorrect repair and modification.

(2) Trouble caused by reasons except the shipped product.

(3) In case of using in range over the value of specification.

(4) In case caused by natural calamity, disaster, and secondary disaster.

Warranty mentioned here means warranty for shipped product itself. Damage caused by trouble of shipped

product is not guaranteed.

[Replacement]

Any inspection and replacement after the expiration of warranty period (one-year) shall be charged to the

purchaser. And also any inspection and replacement which are not covered in warranty mentioned above,

even if it is within warranty period, it shall be charged to the purchaser. If you require the replacement,

please contact your Hitachi distributor.

Содержание SJ-DN2
























































Результаты поиска

Содержание SJ-DN2

Отзывы:

Похожие инструкции для SJ-DN2

Бренды по названию

Популярные бренды

Hitachi SJ-DN2, Инструкция по эксплуатации

Результаты поиска

Содержание SJ-DN2

Отзывы:

Похожие инструкции для SJ-DN2

Бренды по названию

Популярные бренды