Hitachi SJ-DN2 Скачать руководство пользователя страница 14

Страница: 14 / 55

CHAPTER 5 OPERATION

5.2 Operate with Rotational speed command [min

-1

]

Following information indicate the example of the inverter control data at P046: 21, P047: 71 and P049: 4.

See Chapter 6 about explanation of Polled I/O message.

Explanation on each data frame.

[Output frame]

(1) Stop command. Set rotational speed:1800min

-1

(0708hex). Acceleration / Deceleration command are

dependant on the inverter setting. Both rotational speed and run command set from DeviceNet.

(2) Forward running command.

(3) Change rotational speed command: 600min

-1

(0258hex).

(4) Stop command.

(5) Reverse running command. Set rotational speed:1800min

-1

(0708hex).

(6) Stop command.

[Input frame]

(7) Stop condition

(8) While the inverter is forward run condition and accelerating, “XX” represents rotational speed.

(9) Constant speed condition. Revolutions arrive at 1800min

-1

(10) Deceleration condition.

(11) Constant speed run condition. Revolutions arrive at 600min

-1

(12) Deceleration condition.

(13) Stop condition.

(14) The inverter is in the reverse run condition and accelerating.

(15) Constant speed condition. Revolutions arrive at 1800min

-1

(16) Deceleration condition.

(17) Stop condition.

(8)

(7)

(17)

(16)

(15)

(14)

(13)

(12)

(11)

(10)

(9)

1800

min

-1

60
00
08
07

62
00
08
07

60
00
58
02

61
00
58
02

70
03
00
00

78
05
xx
xx

F8
04
08
07

78
04
xx
xx

70
03
00
00

74
05
xx
xx

F4
04
58
02

74
05
xx
xx

F4
04
08
07

74
04
xx
xx

61
00
08
07

70
03
00
00

60
00
08
07

600

min

-1

1800

min

-1

(6)

(5)

(4)

(3)

(2)

(1)

3Byte

0Byte

OUT

Reverse
running

Forward
running

3Byte

0Byte

Содержание SJ-DN2
























































Результаты поиска

Содержание SJ-DN2

Отзывы:

Похожие инструкции для SJ-DN2

Бренды по названию

Популярные бренды

Hitachi SJ-DN2, Инструкция по эксплуатации

Результаты поиска

Содержание SJ-DN2

Отзывы:

Похожие инструкции для SJ-DN2

Бренды по названию

Популярные бренды