Hitachi RAC-10SH3, Руководство по обслуживанию

Страница: 51 / 153

DEUTSCH FRANÇAIS ITALIANO SPANISH PORTUGUÊS
∂ÏÏËÓÈο РУССКИЙ
•
This is for filter cleaning operation check.
•
In basic air-conditioner operation (cooling operation etc.), the filter cleaning operation will not start even when the
(MANUAL CLEAN) button on the remote controller is
pressed.
(
(CLEAN) indicator lit for 1 second/off for 1 second, for 10 seconds)
•
During filter cleaning operation or within 5 minutes after the operation, even when the
(MANUAL CLEAN) button on the remote controller is pressed, the filter
cleaning operation will not restart to protect the device. (
(CLEAN) indicator lit for 1 second/off for 1 second, for 10 seconds)
•
Is “filter cleaning operation prohibited” being set? Please return to the filter cleaning operation setting.
(
(CLEAN) indicator lit for second/off for 1 second, for 10 seconds)
•
Are micro mesh stainless filter
, dust catcher
, filter cleaning wiper
, wiper cover correctly
installed?
(
(CLEAN) indicator lit for 4 seconds/off for 1 second)
•
Filter cleaning is not performed if the air conditioner operation is stopped by Sleep T
imer or Of
f
T
imer function. However
, if the air conditioner is stopped by Sleep
T
imer or Of
f
T
imer every time, filter cleaning will be performed approximately once
a week.
•
A
whirring motor noise is generated due to driving of the cleaning unit.
•
A
clapping noise is generated when the dust catcher collects the dust swept by the
cleaning unit.
•
A
clapping noise is generated when the dust catcher is turned over by the cleaning
unit.
•
A
sweeping sound is generated when the cleaning unit sweeps the dust.
•
After the filter cleaning wiper maintenance, is the cleaning unit return to the right end part using the remote controller?
•
Are micro mesh stainless filter
, dust catcher
, filter cleaning wiper
, wiper cover correctly
installed?
(
(CLEAN) indicator lit for 4 seconds/off for 1 second)
TROUBLESHOOTING
FIL
TER CLEANING OPERA
TION
Filter cleaning is performed after the power is turned on (after the plug-in or after the circuit breaker is switched on after power failure) Filter cleaning operation does not start (
(CLEAN)
indicator blinks or lit and dim repeatedly) Noise occurred during filter cleaning operation Cleaning unit stops halfway
•
Filter may not be cleaned evenly depending on the environment in which the air conditioner is used.
T
o solve this problem, clean the micro mesh stainless filter
.
•
Depending on dust amount, the micro mesh stainless filter may not be completely cleaned by manual filter cleaning operation performed at your preferred time while filter cleaning operation is prohibited.
Micro mesh stainless filter is still dirty
– 41 –
ENGLISH
18SH3_OM.indd 41 18SH3_OM.indd 41
2012-2-21 14:45:472012-2-21 14:45:47
TROUBLESHOOTING (continued)
Anti-mold wasabi cassette
Dust box
ANTI-MOLD W
ASABI CASSETTE
•
Anti-mold elements with wasabi aroma prevents mold growth inside the dust box in which the dust collected by filter cleaning operation is kept.
Although only a trace amount of anti-mold elements is released, there may
be wasabi smell in the room depending on the environment in which the air conditioner is used. If you feel this smell is unpleasant, block one of the anti-mold element outlets with a commercially available adhesive tape. If this measure is taken, the amount of anti-mold element to be released will be reduced and the anti-mold ef
fect
will also be less accordingly
.
T
o prevent mold growth, frequent cleaning of the dust box is recommended.
Outlet (2 places) The gap made on the side surf
ace
Bloc
k one of the outlets with an
adhesiv
e tape (Either one of 2
outlets)
•
Do the batteries need replacement?
•
Is the polarity of the inserted batteries correct?
•
Is the power plug inserted properly?
•
Is the fuse blown out or circuit breaker tripped?
•
Is there a blackout? (Operation remains idle after a blackout.)
•
Is the micro mesh stainless filter blocked with dust?
•
Is the set temperature suitable?
•
Have the vertical air deflector been adjusted to the correct positions according to the operation mode selected?
•
Are the air inlets and air outlets of indoor and outdoor units blocked?
•
Is the fan speed “LOW” or “SILENT”?
•
Check “filter cleaning operation”.
PLEASE CHECK THE FOLLOWING BEFORE SER
VICE
Signal cannot be received (Remote controller display is dim or blank) Operation does not start Does not cool well Does not heat well
(CLEAN)
indicator blinks
– 42 –
18SH3_OM.indd 42 18SH3_OM.indd 42
2012-2-21 14:45:472012-2-21 14:45:47