Hitachi RAC-10SH3, Руководство по обслуживанию, Страница: 37 / 153

SPANISH PORTUGUÊS
∂ÏÏËÓÈο РУССКИЙ
AUTOMA
TIC OPERA
TION
•
• •
nj
1 2
2
1
7(0325$5< 6:,7&+
Based on the room temperature and outside temperature, the unit determines the most suitable operation mode (heating, dehumidifying or cooling) and a comfortable temperature. (Set the current time on the remote controller before starting operation.)
Press the
(AUTOMATIC
OPERATION) button
to set the operation mode to auto.
•
Every time you press it, the mode will change as shown in the chart on the right.
Press the
(ST
OP) button.
Press the
(ST
OP) button again.
A
short beep sounds and the automatic
operation stops. Operation mode will be displayed on the remote controller display
.
Increase Decrease
Adjust the room temperature
Press the
(ROOM
TEMPERA
TURE)
button.
•
Every time you press it, a short beep sounds and the temperature will change by 1°C.
•
is displayed if the temperature is set higher than
the automatically set room temperature by 1°C.
is displayed if the temperature is set lower than the
automatically set room temperature by 1°C.
•
The adjustable temperature range is not higher or lower than 3°C of the automatically set room temperature.
•
Humidity setting cannot be adjusted.
Select the fan speed
Press the
(F
AN SPEED) button.
•
“AUT
O”, “LOW” and “SILENT”
can be selected.
•
Every time you press it, the mode will change as shown in the chart on the right.
Beep
ST
OP
•
Performs heating operation when the room temperature is below 23°C. Set the temperature to be around 23°C.
•
Performs dehumidifying operation when the room temperature is 23~26°C. The preset temperature will be the room temperature at the time of start of air conditioner operation.
•
Performs cooling operation when the room temperature is above 27°C. Set the temperature to be around 27°C.
Room temperature and fan speed can be adjusted to your preference.
AUT
OMA
TIC OPERA
TION
Heating
Dehumidifying
Cooling
Even if dehumidifying operation is set, the air conditioner may not execute dehumidifying if the room humidity
is not very high.
This is not a malfunction.
DEUTSCH FRANÇAIS ITALIANO SPANISH PORTUGUÊS
∂ÏÏËÓÈο РУССКИЙ
– 13 –
ENGLISH
18SH3_OM.indd 1318SH3_OM.indd 13
2012-2-21 14:45:272012-2-21 14:45:27
•
•
•
HEA
TING OPERA
TION
Press the
(HEA
T) button to start heating operation.
Press the
(HEA
T) button.
•
Adjust the room temperature and fan speed to your preference. T
emperature range between 16°C~32°C can be set.
Press the
(ST
OP) button.
A
short beep sounds and heating operation stops.
ST
OP
DEHUMIDIFYING OPERA
TION
3 types of dehumidifying operations can be performed by pressing the
(DEHUMIDIFY) button.
Performs powerful dry operation without lower down the room temperature.
Press the
(DEHUMIDIFY) button.
•
Every time you press the
(DEHUMIDIFY) button,
the mode will change as shown in the chart below
.
Condensation
Control
Auto
Dehumidifying
Quick
Laundry
(“AUT
O” flashes for 5 seconds)
•
In auto dehumidifying mode, fine adjustment of room temperature,
humidity
adjustment and fan speed selection can
be made to your
preference.
Every time you press the ROOM TEMPERATURE button, the temperature will change
by 1°C. (Temperature setting range is not higher or lower than 3°C.) Every time you press the HUMIDITY button, the humidity will change by 5%. (Humidity setting range is 40%~70%.)
•
In quick laundry mode, fine adjustment of room temperature and fan speed
Press the
(ST
OP) button.
•
A
short beep sounds and dehumidifying operation stops.
ST
OP •
After the dehumidifying operation is stopped, the remote controller will display the operation mode that had been set before the
(DEHUMIDIFY)
button
was
pressed.
ENGLISH
DEUTSCH FRANÇAIS ITALIANO SPANISH PORTUGUÊS
∂ÏÏËÓÈο
РУССКИЙ
– 14 –
selection can be made to your preference. (Fine adjustment of room temperature and humidity adjustment cannot be made in condensation control mode.)
18SH3_OM.indd 14 18SH3_OM.indd 14
2012-2-21 14:45:272012-2-21 14:45:27