Hitachi H8/3660 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 463

background image

83

Bit 3—Noise Elimination Sampling Frequency Select (NESEL): This bit selects the frequency
at which the watch clock signal (ø

W

) generated by the subclock pulse generator is sampled, in

relation to the oscillator clock (ø

OSC

) generated by the system clock pulse generator. When ø

OSC

= 2

to 10 MHz, clear NESEL to 0.

Bit 3: NESEL

Description

0

Sampling rate is ø

OSC

/16

(Initial value)

1

Sampling rate is ø

OSC

/4

Bits 2 to 0—Reserved Bits: Bits 2 to 0 are reserved: they are always read as 0 and cannot be
modified.

6.2.2

System Control Register 2 (SYSCR2)

Bit

7

6

5

4

3

2

1

0

SMSEL

LSON

DTON

MA2

MA1

MA0

SA1

SA0

Initial value

0

0

0

0

0

0

0

0

Read/Write

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

SYSCR2 is an 8-bit read/write register for power-down mode control.

Upon reset, SYSCR2 is initialized to H'00.

Bit 7—Sleep Mode Selection (SMSEL): This bit chooses the transition to the sleep mode or
subsleep mode when the SLEEP instruction is executed. The transition after the SLEEP instruction
is executed depends on a combination of this and other control bits.

Bit 7: SMSEL

Description

0

A transition is made to sleep mode.

(Initial value)

1

A transition is made to subsleep mode.

Bit 6—Low Speed on Flag (LSON): This bit chooses the system clock (ø) or subclock (ø

SUB

) as

the CPU operating clock. The resulting operation mode after the SLEEP instruction is executed
depends on the combination of other control bits.

Bit 6: LSON

Description

0

The CPU operates on the system clock (ø)

(Initial value)

1

The CPU operates on the subclock (ø

SUB

)

«
...
97
98
99
100
101
...
»

Содержание H8/3660
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8/3660

Бренд: D-Link Страницы: 15

Бренд: CAME Страницы: 19

Бренд: IEI Technology Страницы: 187

Бренд: IEI Technology Страницы: 71

WS-650 lite Series

Бренд: Laurell Страницы: 84

COMSPHERE 3800 Series

Бренд: Paradyne Страницы: 88

COMSPHERE 3800PLUS

Бренд: Paradyne Страницы: 5

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: LORD Страницы: 9

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

Бренд: UNA AUTOMATION Страницы: 20

Бренд: Qlogic Страницы: 8

Бренд: ZALMAN Страницы: 5

RouterBOARD 411R

Бренд: 4gon Страницы: 2

Бренд: SeaLevel Страницы: 34

Бренд: Abit Страницы: 22

Suzie-Q 541.35.520

Бренд: Hafele Страницы: 12

Бренд: M-system Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды