Hinowa HS701 Скачать руководство пользователя

Страница: 74 / 108

6.3.4 E

NGINE AIR FILTER MAINTENANCE

It is a good thing to clean the filter element on a daily basis.
In case of excessive dirt replace the filter.

The filter element must be replaced every 6 times of cleaning or after a year’s work.

Turn off the engine before performing maintenance of the air filter.

Any time you perform maintenance of the air filter, make sure that all hoses are in
good condition and the clamps are properly tightened.

Please follow the steps below for the main‐
tenance of the filter element:

• Open the engine cover.
• Unscrew the latch. Remove the cover (B)

and laydown it in the bonnet. Be carefully
to avoid damages to the gummy tube for
air inlet.

• Remove the cartridge.
• Check that dirt filter element is not dama‐

ged.

• To clean the element, use clean dry compressed air on the inside of the element.

Air pressure at the nozzle must not exceed 205 kPa (2.1 kgf/cm

, 30 psi).

Maintain reasonable distance between the nozzle and the filter.

• Clean the inside of the filter box with a clean cloth.
• Reinstall the cartridge in its casing and then screw the latch.
• Reinstall the cover.

OMPACT DUMPER

HS701 ‐ H

INOWA

MUHS70120615

IMPORTANTE

IMPORTANT

Содержание HS701













































































































Результаты поиска

Содержание HS701

Отзывы:

Похожие инструкции для HS701

Бренды по названию

Популярные бренды

Hinowa HS701, Руководство пользователя - Безопасность и обслуживание машины

Результаты поиска

Содержание HS701

Отзывы:

Похожие инструкции для HS701

Бренды по названию

Популярные бренды