Hino Motors HINO 155 series Скачать руководство пользователя страница 750

Страница: 750 / 860

ENGINE (J05E)/TROUBLESHOOTING

2–714

Connect the signal check harness to engine ECU.

Set the starter key to the "ON" position.

Use the electrical tester to measure the voltage between the termi-
nals of the air flow sensor vehicle side connector.

YES

Set the starter key to the "LOCK" position.

Connect the air flow sensor connector.

Start the engine.

Use an oscilloscope to measure the signal voltage between the
terminals of the engine ECU (signal check harness).

YES

Inspect the air flow sensor power supply

B+

E2G

SHTS021270300651

Measurement

conditions

Tester

connections

Standard values

Starter key: ON

Air flow sensor
vehicle side con-
nector terminals
+B

–

E2G

11.5

–

13.5 V

Do the measurements meet the standard value?

Go to step 7.

Replace the engine ECU.

Inspect the air flow sensor signal unit

E74

E78

SHTS021270300652

Measurement

conditions

Tester

connections

Standard values

After warm up, the
engine idling con-
dition

Engine ECU
(the signal check
harness)
VG (E74)

–

EVG (E78)

–

6 kHz

Do the measurements meet the standard value?

Go to step 8.

Replace the air flow sensor.
Perform "After-inspection work" of INFOR-
MATION section.

Содержание HINO 155 series





























































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HINO 155 series

Отзывы:

Hino Motors HINO 155 series, Руководство по ремонту, Страница: 750 / 860

Результаты поиска

Содержание HINO 155 series

Отзывы: