manualshive.com logo in svg

Hino Motors HINO 155 series, Руководство по ремонту, Страница: 394 / 860

Поделиться
Скачать
Hino Motors HINO 155 series Скачать руководство пользователя страница 394

ENGINE (J05E)/TROUBLESHOOTING

2–358

DTC: P0219

EN01H02127030602016060

P0219: Engine overspeed condition

INFORMATION

1.

Technical description

•

The engine ECU detects the engine speed using the engine speed main sensor (crankshaft position sensor)
mounted on the flywheel housing.

<Description of malfunction>

•

Engine speed above rated value is detected.

2.

DTC set condition

(1)

DTC detection condition
While the engine is in operation

(2)

Judgement criteria
An engine speed of more than 3,000 r/min

3.

Reset condition

•

After restoration to normal condition

4.

Indication, warning or system control regulation when the DTC is set.

•

MIL: OFF

•

SVS light: OFF

•

Cruise control function is not available.

•

Accelerator is fully closed.

•

EGR valve is fully closed.

•

VNT is fully open.

•

Diesel throttle is fully closed.

5.

Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Cruise control does not work.

<Symptoms on the vehicle due to malfunction>

•

–

6.

Pre-inspection work

•

Check that the battery voltage is in the normal range.

7.

After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is stored after test drive.

X3F

ZTZ

J0J

1mA

(NE-)

(SNE)

XK4

J0H

1mA

(NE+)

(NE-)

(NE+)

Engine ECU

Engine speed main sensor

SHTS021270300322

Содержание HINO 155 series





























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов