Hino Motors HINO 155 series Скачать руководство пользователя страница 144

Страница: 144 / 860

ENGINE (J05E)/TROUBLESHOOTING

2–108

DTC: P0006 and P0007

EN01H02127030602016024

P0006: Malfunction of fuel cut valve (Low)

INFORMATION

Technical description

•

–

<Description of malfunction>

•

Fuel cut valve is not working properly.

•

Possible magnetic valve failure or harness GND short-circuit

DTC set condition

(1)

DTC detection condition

•

Fuel cut valve inactivity request is in progress.

•

Starter key "ON".

•

Battery voltage is in the range of 10 V to 16 V.

(2)

Judgement criteria

•

The condition that the fuel cut valve circuit voltage is 2.8 V or less remains for 3 seconds or more.

Reset condition

•

Immediately after normal operation is restored.

Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

SVS light: OFF

Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

–

<Symptoms on the vehicle due to malfunction>

•

DPR automatic regeneration may not be performed properly.

Pre-inspection work

•

Check that the battery voltage is in the normal range.

After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is detected after test drive.

Estimated failure factors

•

GND short-circuit in fuel cut valve signal line

•

Malfunction of fuel cut valve

•

Malfunction of engine ECU

EB4

EBP

TYP 0.7A

(FCV)

Engine ECU

Fuel cut valve

FCV

SHTS021270300099

Содержание HINO 155 series





























































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HINO 155 series

Отзывы:

Hino Motors HINO 155 series, Руководство по ремонту, Страница: 144 / 860

Результаты поиска

Содержание HINO 155 series

Отзывы: