HIKVISION 607 Series Скачать руководство пользователя страница 80

Страница: 80 / 163

607 Series Face Recognition Terminal

User Manual

Click

to select the upgrade file.

Click Upgrade to start upgrading.

Note:

Do not power off during the upgrading.

Configuring RS-485 Parameters

Purpose:
You can set the RS-485 parameters including the baud rate, data bit, stop bit, parity type,
communication mode, work mode, and connection mode.

Note:

The RS-485 Settings should be supported by the device.

Steps:
1.

In the Remote Configuration page, click System -> RS-485 Settings to enter the Configuring the
RS-485 Parameters tab.

Select the serial No. of the port from the dropdown list to set the RS-485 parameters.

Set the baud rate, data bit, the stop bit, parity, flow control, communication mode, working
mode, and the connection mode from the dropdown list.

Click Save to save the settings and the configured parameters will be applied to the device
automatically.

Note:

After changing the working mode, the device will be rebooted. A prompt will be popped up

after changing the working mode.

Содержание 607 Series




































































































































































Результаты поиска

Содержание 607 Series

Отзывы:

HIKVISION 607 Series, Руководство пользователя, Страница: 80 / 163

Результаты поиска

Содержание 607 Series

Отзывы: