HIKVISION 607 Series Скачать руководство пользователя страница 16

Страница: 16 / 163

607 Series Face Recognition Terminal

User Manual

Chapter 3

Installation

3.1

Installation Environment



If installing the device indoors, the device should be at least 2 meters away from the light, and
at least 3 meters away from the window or the door.



If installing the device outdoors, you should apply Sililcone sealant among the cable wiring
area to keep the raindrop from entering.



Make sure the environment illumination is more than 100 Lux.

Notes:



For details about installation environment, see Appendix C Tips for Installation Environment.



Make sure the output of external power supply fulfils LPS.

3.2

Installing with Gang Box

Steps:

According to the datum line on the mounting template, stick the mounting template on the wall

or other surface, 1.4 meters higher than the ground.

Drill holes on the wall or other surface according to the mounting template and install the gang

box.

Use two supplied screws (4_KA4 × 22-SUS) to secure the mounting plate on the gang box.

Содержание 607 Series




































































































































































Результаты поиска

Содержание 607 Series

Отзывы:

HIKVISION 607 Series, Руководство пользователя, Страница: 16 / 163

Результаты поиска

Содержание 607 Series

Отзывы: