HIKVISION 607 Series Скачать руководство пользователя страница 132

Страница: 132 / 163

607 Series Face Recognition Terminal

User Manual

122

Click Access Control Alarm tab to enter the following interface.

Steps:

All access control alarms will display in the list in real time.
You can view the alarm type, alarm time, location, etc.

Click

to view the alarm on E-map.

You can click

to view the live view or the captured picture of the triggered camera

when the alarm is trigged.

Note:

For setting the triggered camera, refer to Chapter 7.10.1 Access Control Event Linkage.

Click Subscribe to select the alarm that the client can receive when the alarm is triggered.

Check the checkbox(es) to select the alarm(s), including device exception alarm, door event
alarm, card reader alarm, and alarm input.

Click OK to save the settings.

Содержание 607 Series




































































































































































Результаты поиска

Содержание 607 Series

Отзывы:

HIKVISION 607 Series, Руководство пользователя, Страница: 132 / 163

Результаты поиска

Содержание 607 Series

Отзывы: