HIKVISION 607 Series Скачать руководство пользователя страница 124

Страница: 124 / 163

607 Series Face Recognition Terminal

User Manual

114

Table 1. 1

Linkage Actions for Access Control Event

Linkage Actions

Descriptions

Audible Warning

The client software gives an audible warning when alarm is
triggered. You can select the alarm sound for audible warning.

Email Linkage

Send an email notification of the alarm information to one or
more receivers.

Alarm on E-map

Display the alarm information on the E-map.

Note:

This linkage is only available to access control point and

alarm input.

Alarm Triggered

Pop-up Image

The image with alarm information pops up when alarm is
triggered.

7.10.2

Event Card Linkage

Click Event Card Linkage tab to enter the following interface.

Note:

The Event Card Linkage should be supported by the device.

Содержание 607 Series




































































































































































Результаты поиска

Содержание 607 Series

Отзывы:

HIKVISION 607 Series, Руководство пользователя, Страница: 124 / 163

Результаты поиска

Содержание 607 Series

Отзывы: