HENGBO HB-2020 Series страница 9 Скачать руководство пользователя

Страница: 9 / 30

operation of built-in speaker in the wireless receiving host. The siren

is optional according to specific requirements.

Wiring

Wiring connection

connection

connection is

is shown

shown

shown as

as the

the

the Figure

Figure

Figure below.

below.

VI.

VI. System

System

System Installation

Installation

1. Basic Requirements of System Installation

①

During installation, suitable types and models of defense

products should be adopted according to user ’s requirements for

defense areas.

②

The installation location, angle and height of defense products

shall be determined according to the effective defense zone of defense

products and site conditions. The defense products shall be installed in

hidden locations as much as possible which must be in compliance

with defense requirements.

③

The type of defense zones in each location should be labeled

on the orientation drawing.

④

The orientation drawing should be archived for system

maintenance.

2. System

System

System Installation

Installation

Installation and

and

and Debugging

Debugging

－－

The wireless receiving host should be placed on a table which is

near to window as far as possible.

－－

The wireless receiving host has no explosion-proof function,

which cannot be directly installed in Class I, II or III hazardous

locations ( i.e. locations where ignitable concentration of flammable,

Содержание HB-2020 Series































Результаты поиска

Содержание HB-2020 Series

Отзывы:

Похожие инструкции для HB-2020 Series

Бренды по названию

Популярные бренды

HENGBO HB-2020 Series, Руководство пользователя

Результаты поиска

Содержание HB-2020 Series

Отзывы:

Похожие инструкции для HB-2020 Series

Бренды по названию

Популярные бренды