background image

26

Backup battery can’t

work normally when

power failure occurs.

Check whether the polarity of backup

battery

is wrongly

connected,

or

check whether backup battery fuse

has burnt out.

backup battery out of life

Check

if

the

polarity

connection of backup battery

is correct, or check if the fuse

has burnt out.

recharge the backup battery

There is low-voltage

warning

tone

when

alarm

host provides

power

by

backup

battery.

Backup battery power lower.

Backup battery is invalid.

Recharge backup battery.

Change backup battery.

The receiving distance

of the host becomes

shorter

Antenna is damaged.

The host shares the same socket with

TV and microwave oven etc.

Close to TV and microwave oven etc.

Replace the antenna.

It is recommended to use an

independent power socket.

Avoid close to devices with

high

electromagnetic

radiation.

Alarm information can

not be

received

in

some defense zones.

The code for this zone has been

deleted.

This zone has been bypassed by the

host.

Relearn

code

under

the

direction of the distributor.

Arm this zone again according

to user manual.

Detector

Misinformation

The installation position does not

comply with installation

requirements.

The power of backup battery is low or

invalid.

Adjust

installation

position

according

to

installation

requirements.

Check backup battery.

The wireless detecting

distance of wireless

detectors becomes

shorter.

The installation position of the

detector is not suitable.

The installation conditions are subject

to interruption or obstruction.

Adjust installation position

The distance of

The emitting indicator lamp does not

Battery power low, it needs to

Содержание HB-2020 Series































Отзывы: