Heiko Thermal Plus 12 Скачать руководство пользователя страница 57

Страница: 57 / 110

5. Installation Walkthrough

5.7. Wiring

5.7.4. Wiring Process Preliminary Precautions

•

Please ensure that a suitable circuit breaker is used for the heat pump.

•

The power supply to the heat pump unit must be grounded.

•

Wiring should be done by a licensed professional, and comply with industry regulations.

•

The unit should be completely powered off before any wiring is done.

•

Cables should be properly fastened into place, to prevent loosening from occurring.

•

No cable should be fastened to another.

•

The power supply should be compliant to all standards located in the rating label.

•

The power supply, necessary cables, and sockets should fully meet the input power

requirements of the unit.

Main power
in user side

R S T N PE

Main power cable

Power cable for anti-freeze

electric heater

Signal cable

Sensor cable

Main power
in user side

L N PE

Содержание Thermal Plus 12















































































































Результаты поиска

Содержание Thermal Plus 12

Отзывы:

Похожие инструкции для Thermal Plus 12

Бренды по названию

Популярные бренды

Heiko Thermal Plus 12, Руководство пользователя

Результаты поиска

Содержание Thermal Plus 12

Отзывы:

Похожие инструкции для Thermal Plus 12

Бренды по названию

Популярные бренды