manualshive.com logo in svg

Heatrae Sadia ELECTROMAX SOLAR, Инструкция по установке и обслуживанию

Поделиться
Скачать
Heatrae Sadia ELECTROMAX SOLAR Скачать руководство пользователя страница 76

76

11.0 GUARANTEE

This 

Electromax Solar 

is guaranteed against faulty materials and manufacture provided that:

The Electomax Solar has been installed in accordance with the installation and service 

• 

instructions and all relevant Codes of Practice and Regulations in force at the time of instal-

lation, and that all necessary controls and safety valves have been fitted correctly.

Any valves and controls fitted are of Heatrae Sadia recommended type and specifica

-

• 

tion.

The Electromax Solar has not been modified or tampered with in any way, and has been 

• 

regularly maintained as detailed in these instructions.

The domestic hot water cylinder has only been used for the storage of wholesome water 

• 

as defined by the Water Supply (Water Fittings) Regulations 1999.

The central heating primary circuit has been flushed and treated with a suitable inhibitor 

• 

and is used only for domestic heating purposes.

Within 60 days of installation the user completes and returns the guarantee registration 

• 

card supplied with the unit in order to register the product.

The unit is not guaranteed against damage by frost, and the immersion heaters are not guar-

anteed against excessive scale build-up.

Periodic loss of charge pressure from the expansion vessels is normal (indicated by an in-

termittent discharge of water from the pressure relief valves) and is not covered under the 

product guarantee. 

The following guarantee periods apply from the date of purchase:

Stainless steel domestic hot water cylinder 

10 years

All other components 

 

 

 

2 years

This guarantee does not affect your statutory rights.

12.0 ENVIRONMENTAL INFORMATION

This product is manufactured from many recyclable materials. At the end of its useful life it 

should be disposed of at a Local Authority Recycling Centre in order to realise the full envi-

ronmental benefits.

Insulation of the domestic hot water cylinder is by means of an approved CFC/HCFC free 

polyurethane foam with an ozone depletion factor of zero and a Global Warming Potential 

(GWP) of 3.1.

Содержание ELECTROMAX SOLAR

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды