Heatrae Sadia ELECTROMAX SOLAR Скачать руководство пользователя страница 43

Страница: 43 / 80

4.8 COMMISSIONING - SOLAR CONTROLLER

The solar controller is pre set at the factory and should require no adjustment. The following

sections are provided for infomation purposes only.

The Electromax Solar control panel incorporates a micro processor based differential tem-

perature controller which contains many functions to regulate and monitor the solar primary

system, this includes:

Functions for heating the solar cylinder

•

Functions to monitor the solar system

•

Functions to protect the solar system

•

The controller collects temperatures from the sensors located in the solar collector and the

solar cylinder and determines the right time to charge the storage tank ( i.e. turn the pump

on and off ).

4.8.1 CHANGING VALUES

The Solar controller user interface comprises an LCD screen and four buttons through which

information may be viewed and altered as described in the sections below.

4.8.2 LCD SCREEN

The LCD screen is split into four sections:

Main menu

•

Display values

•

Measuring points

•

Status indication

•

FIGURE 26: SOLAR CONTROLLER

LCD DISPLAY

BUTTONS

FIGURE 27: SOLAR CONTROL LCD DISPLAY

MAIN MENU

DISPLAY VALUES

MEASURING POINTS ASSIGNMENT

STATUS INDICATION

Содержание ELECTROMAX SOLAR

















































































Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды

Heatrae Sadia ELECTROMAX SOLAR, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды