Heatrae Sadia ELECTROMAX SOLAR Скачать руководство пользователя страница 54

Страница: 54 / 80

7.0 FAULT FINDING

WARNING: DISCONNECT FROM ALL ELECTRICAL SUPPLIES BEFORE BEGINNING ANY

WORK ON THE ELECTROMAX SOLAR. FLUID CONTAINED IN THE DOMESTIC HOT WA-

TER, CENTRAL HEATING AND SOLAR CIRCUITS MAY BE VERY HOT!

The Electromax Solar should give trouble free operation, however should a problem occur,

the tables below should enable most faults to be identified with ease.

Fault Finding should be carried out by a competent person and any replacement parts used

should be authorised Heatrae Sadia Electromax Solar spare parts.

7.1 FAULT FINDING - DOMESTIC HOT WATER

FAULT

POSSIBLE CAUSE

REMEDY

No water

Mains supply switched off.

Check and open stop cock.

Strainer blocked

Turn off water supply. Remove

strainer and clean.

Cold water combination valve

is fitted incorrectly

Check and re fit as required.

No hot water

Off Peak electrical supply

switched off

Check and switch on.

Off Peak immersion thermostat

setting too low

Check and adjust setting is

required.

Off Peak immersion heater cut

out has operated

Check and reset by pushing

button.

Off Peak immersion heater has

failed

Check and replace if required.

No solar gain

Go to 7.2

No boost

Boost electrical supply

switched off

Check and switch on.

Boost immersion thermostat

setting too low

Check and adjust setting is

required.

Boost immersion heater cut out

has operated

Check and reset by pushing

button.

Boost immersion heater has

failed

Check and replace if required.

Water discharges from expan-

sion relief valve

Expansion vessel volume has

reduced.

Check pressure and re charge

if required

Cold water combination valve

not working correctly

Check pressure from valve.

If greater than 3 bar replace

pressure reducer cartridge.

Expansion valve seat dam-

aged.

Remove expansion relief valve

and check condition of seat.

Replace if necessary.

Water discharges from temper-

ature and pressure relief valve

Thermal control failure

Switch off power. DO NOT

turn off water supply. Check all

thermal controls and replace if

faulty

Содержание ELECTROMAX SOLAR

















































































Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды

Heatrae Sadia ELECTROMAX SOLAR, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды