Heatrae Sadia ELECTROMAX SOLAR Скачать руководство пользователя страница 24

Страница: 24 / 80

3.6.3 SOLAR EXPANSION VESSEL

A 24 litre solar expansion vessel is supplied with the Electromax Solar collector kits. Use only

the Solar Expansion vessel supplied with these kits.

The Solar Expansion Vessel is wall mounted. A mounting bracket is supplied with the collec-

tor kits for this purpose. When full the Solar Expansion Vessel can weigh 28Kg. Ensure the

wall can take the weight of the solar expansion vessel when full.

The solar expansion vessel should be connected to the solar return pipework. A short length

of flexible stainless steel tube (600mm) is supplied to make this connection.

A self sealing connection is supplied in the solar connector kit which should be screwed onto

the solar expansion vessel connection before connecting the flexible stainless steel tube.

The solar expansion Vessel should be sited as close to the Electromax Solar as practicably

possible, allowing access to both the Electromax Solar and the expansion vessel for servic-

ing and maintenance.

The solar expansion vessel must be installed so that the connection is at the top.

FIGURE 12: SOLAR EXPANSION VESSEL

ELECTROMAX

SOLAR

FLOW

SOLAR

RETURN

SOLAR

EXPANSION

VESSEL

SELF SEALING

CONNECTION

Содержание ELECTROMAX SOLAR

















































































Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды

Heatrae Sadia ELECTROMAX SOLAR, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды