Heatrae Sadia ELECTROMAX SOLAR Скачать руководство пользователя страница 29

Страница: 29 / 80

3.8 INSTALLATION - ELECTRICAL

WARNING: THIS APPLIANCE MUST BE EARTHED. IT IS SUITABLE FOR A.C. SUPPLY ONLY.

ELECTRICAL INSTALLATION MUST BE CARRIED OUT BY A COMPETENT ELECTRICIAN

AND BE IN ACCORDANCE WITH THE LATEST I.E.E. WIRING REGULATIONS.

ENSURE THE ELECTRICAL SUPPLY IS SWITCHED OFF BEFORE MAKING ANY

CONNECTIONS TO THE ELECTROMAX SOLAR.

Installation of the electrical system requires:

Connection to a 240v 45A supply for the boiler

•

Connection to a 240v 16A for the control panel and boost immersion heater

•

Connection to a 240v 16A off peak supply for the immersion heater

•

Connection to the room thermostat

•

Connection to the solar collector sensor.

•

Connection to the solar divertor valve (if fitted).

•

The electrical supply to the property must be checked to ensure it is of sufficient current rating

and voltage.

The consumer unit must be fitted with a double pole 30mA RCD.

The electric boiler circuit must include a 45A MCB in the circuit.

The immersion heaters must include a 16A MCB in each circuit

Each circuit must incorporate an isolating switch with a contact separation of at least 3mm

in both poles.

Immersion heater, boiler and room thermostat cables must be routed via the cable entry holes

in either the right or left hand side of the upper panel. There are four holes in each side, one

25mm hole and three 20mm holes.

FIGURE 16: CABLE GLANDS

CABLE

GLANDS

Содержание ELECTROMAX SOLAR

















































































Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды

Heatrae Sadia ELECTROMAX SOLAR, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды