Heatrae Sadia ELECTROMAX SOLAR Скачать руководство пользователя страница 49

Страница: 49 / 80

5.0 DEMONSTRATION TO USER

Following commissioning all panels and covers must be replaced and fully secured.

Operation of the Electromax Solar should be explained fully to the user:

5.1 ELECTROMAX SOLAR CONTROL PANEL

Demonstrate how the control cover is opened and closed.

Explain what each of the switches does and what each of the indicators / displays show.

5.2 DOMESTIC HOT WATER

Explain how the whole cylinder is heated when there is sufficient solar energy.

Explain how part of the cylinder is heated by the lower immersion heater if sufficient

solar energy is not available.

Explain how the one hour boost immersion heater is operated.

5.3 CENTRAL HEATING

Explain how the central heating system works.

Explain how the programmable room thermostat is operated and how it has been set.

5.4 SYSTEM MALFUNCTION

Explain how to isolate electrical and water supplies in the case of a system fault.

Explain that a qualified plumber and or electrician should be contacted if there is a sys

tem fault.

Explain how to identify / check for basic system faults:

Hot water temperature

•

Central heating temperature

•

Pressure relief valve discharge

•

Solar and central heating system pressures

•

Electric boiler alarm indicator

•

Solar controller alarm indicator

•

5.5 SYSTEM MAINTENANCE

Explain the necessity to carry out regular maintenance of the Electromax Solar to en-

sure its continued safe and efficient operation.

5.6 LITERATURE

Hand over the following literature:

Electromax Solar installation instructions

•

Electromax Solar collector installation instructions

•

Electromax Solar user instructions

•

Programmable room thermostat instructions

•

Содержание ELECTROMAX SOLAR

















































































Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды

Heatrae Sadia ELECTROMAX SOLAR, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды