Heatrae Sadia ELECTROMAX SOLAR Скачать руководство пользователя страница 30

Страница: 30 / 80

Solar sensor and divertor valve wires must be routed via the two cable entry holes at the back

of the Electromax Solar.

Cable glands and snap fit blanking plugs are supplied with the Electromax Solar. The cable

glands should be fitted into the cable entry holes selected for cable entry and secured in place

using the locknuts supplied.

The cable glands must be used to secure the electrical supply cables, the solar collector sensor

cable and the divertor valve cable (if fitted). Failure to do so can result in cables straining

internal electrical connections and lead to electrical failure. Failure due to inadequate cable

securing will not be covered by warranty.

The remaining holes not used should be blanked off using the snap fit blanking plugs

supplied.

Connection of all cables requires removal of top and front panels and removal of the control

panel rear cover. Refer to page 11 for panel removal.

3.8.1 240v 16A CONTROL PANEL AND BOOST IMMERSION HEATER CONNECTION

Connection of the control panel and boost immersion heater cable is made to the main terminal

block located behind the Electromax Solar control panel.

Use 3 core 1.5mm

•

flexible cable

Route the cable via one of the 20mm cable glands

•

Connect the Live (brown) conductor to terminal L2

•

Connect the Neutral (blue) conductor to terminal N2

•

Connect the Earth (green/yellow) one of the conductors marked

•

3.8.2 240v 16A IMMERSION HEATER CONNECTION

Connection of the immersion heater is made to the main terminal block located behind the

Electromax Solar control panel.

Use 3 core 1.5mm

•

flexible cable

Route the cable via one of the 20mm cable glands

•

Connect the Live (brown) conductor to terminal L1

•

Connect the Neutral (blue) conductor to terminal N1

•

Connect the Earth (green/yellow) one of the conductors marked

•

3.8.3 PROGRAMMABLE ROOM THERMOSTAT CONNECTION

Connection of the room thermostat cable is made to the main terminal block located behind

the Electromax Solar control panel.

Use 2 core 0.5mm

•

or 1.0mm

flexible cable suitable for 240v.

Route the cable via one of the 20mm cable glands

•

Connect room thermostat COM terminal B

•

Connect room thermostat N/O to terminal A

•

DO NOT connect to room thermostat N/C

•

Содержание ELECTROMAX SOLAR

















































































Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды

Heatrae Sadia ELECTROMAX SOLAR, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды