Heatrae Sadia ELECTROMAX SOLAR Скачать руководство пользователя страница 11

Страница: 11 / 80

3.0 INSTALLATION

3.1 INSTALLATION - G ENERAL

It is recommended that installation of the Electromax Solar is carried out in the following

order:

Location

•

Domestic Hot Water

•

Solar

•

Central Heating

•

Electrical

•

3.2 PANEL REMOVAL

Installation will require removal of the panels:

TOP PANEL - Unscrew the two screws located on the top face, about two thirds of the

•

way back, pull panel towards you and lift up.

LOWER FRONT PANEL - Pull the panel forward.

•

FRONT PANEL - Remove the lower front panel. Unscrew the two screws located either

•

side at the bottom of the front panel and pull the panel forwards.

FRONT INSULATION - Remove front and lower front panel and pull front insualtion piece

•

away from pipework manifolds.

CONTROL PANEL - Remove top panels, front panels and front insulation piece. Unscrew

•

the two screws located either side at the top of the control panel and allow the control

panel to drop forwards.

CONTROL PANEL REAR COVER - Open the control panel. Unscrew the two screws

•

located either side of the control panel rear cover and remove the rear cover.

TOP

PANEL

TOP PANEL

SCREWS

FRONT

PANEL

FRONT

PANEL

SCREWS

LOWER

FRONT

PANEL

CONTROL PANEL

SCREWS

REAR COVER

SCREWS

FIGURE 04: PANEL REMOVAL

FRONT

INSULATION

Содержание ELECTROMAX SOLAR

















































































Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды

Heatrae Sadia ELECTROMAX SOLAR, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ELECTROMAX SOLAR

Отзывы:

Бренды по названию

Популярные бренды