Heatilator HEIR36 Скачать руководство пользователя | Manualshive

Страница: 49 / 60

background image

49

Heatilator • HEIR36, HEIR42, HEIR50 Installation Manual • 2285-980 Rev. G • 12/14

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath

the

fi

rebox.

• The splatter guard is a piece of corrugated material

used to protect the appliance during the installation
process before

fi

nishing work on the whole hearth is

complete. Splatter guards may be factory installed
or accompany the decorative front of the unit, de-
pending on the

fi

replace model. Splatter guards

must be removed before appliance is

fi

red.

WARNING! Risk of Fire!

Close the ball valve before in-

stalling the splatter guard to prevent accidental lighting.
Remove the splatter guard before lighting the appliance.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated
inside the

fi

rebox or underneath in the control cavity.

E. Glowing Ember Placement

WARNING! Risk of Explosion!

Follow ember placement

instructions in manual. DO NOT place embers directly over
burner ports. Replace ember material annually. Improperly
placed embers interfere with proper burner operation.

Ember material is shipped with this gas appliance. To place
the ember material:
• Embers CANNOT be placed directly over ports. Care

should be taken not to cover the lighting trail of ports
(from back to front).

• Place dime-size pieces of Glowing Embers® just in front

of the port trail, but not on or in between the ports (see
Figure 11.10). Care should be taken so that the ports are
not covered. Failure to follow this procedure will likely
cause lighting and sooting problems.

• Save the remaining ember materials for use during

appliance servicing. The embers provided should be
enough for 3 to 5 applications.

D. Lava Rock and Mystic Ember Placement

1. Apply the lava rock and Mystic Embers as shown in

Figure 11.9. The lava rock and Mystic Embers are
to be placed around the base hearth refractory and
can be used to conceal the joints of the hearth base
refractory pieces.

Figure 11.9. Apply Mystic Embers

Figure 11.10. Location of Glowing Embers

APPLY GLOWING EMBERS

ADJACENT TO PORTS

«
...
47
48
49
50
51
...
»

Содержание HEIR36





























































Отзывы:

Нет отзывов

Похожие инструкции для HEIR36

Бренд: Warm House Страницы: 26

Бренд: Majestic Страницы: 2

Бренд: Majestic Страницы: 24

Бренд: Majestic Страницы: 63

Бренд: Majestic fireplaces Страницы: 36

Бренд: Majestic fireplaces Страницы: 16

Бренд: Majestic fireplaces Страницы: 28

Бренд: Majestic Страницы: 24

Бренд: Napoleon Страницы: 4

Бренд: Napoleon Страницы: 4

Бренд: Napoleon Страницы: 2

Бренд: Vanguard Страницы: 30

Бренд: PSF Страницы: 2

Бренд: Napoleon Страницы: 80

Бренд: Valor Страницы: 29

Бренд: Cal Flame Страницы: 32

Бренд: Continental Fireplaces Страницы: 48

Бренд: Hargrove Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды