Heatilator HEIR36 Скачать руководство пользователя

Страница: 55 / 60

Heatilator • HEIR36, HEIR42, HEIR50 Installation Manual • 2285-980 Rev. G • 12/14

G. Install Decorative Front

WARNING! Risk of Fire!

Install ONLY decorative fronts

approved by Hearth & Home Technologies. Unapproved
decorative fronts may cause

replace to overheat.

This fireplace has been supplied with an integral
barrier to prevent direct contact with the

xed glass

panel. DO NOT operate the

replace with the barrier

removed.

Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.

For more information refer to the instructions supplied with
your decorative front.

Figure 12. Log Set Installed

Log #6 (2285-706)

: Place Log #6 into appliance as shown in Figure 12. Bottom corner of Log #6 should be about 1/2 inch

from right hand grate tine. Log will contact right center grate tine. The top of Log #6 should rest in the notch on Log #2.

LOG CONTACTS

GRATE TINE

1/2 IN.

(APPROXIMATELY)

2285-935

Содержание HEIR36





























































Результаты поиска

Содержание HEIR36

Отзывы:

Похожие инструкции для HEIR36

Бренды по названию

Популярные бренды

Heatilator HEIR36, Руководство по установке

Результаты поиска

Содержание HEIR36

Отзывы:

Похожие инструкции для HEIR36

Бренды по названию

Популярные бренды