Heatilator HEIR36 Скачать руководство пользователя

Страница: 41 / 60

Heatilator • HEIR36, HEIR42, HEIR50 Installation Manual • 2285-980 Rev. G • 12/14

Finishing

A. Facing Material

• Metal front faces may be covered with non-combustible

materials only.

• Facing and/or

nishing materials must not interfere

with air

ow through louvers, operation of louvers or

decorative fronts, or access for service.

• Facing and/or

nishing materials must never overhang

into the glass opening.

• Observe all clearances when applying combustible

materials.

WARNING! Risk of Fire! DO NOT

apply combustible

materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as speci

ed in

this manual. Overlapping materials could ignite and will
interfere with proper operation of decorative fronts and
louvers.

Figure 10.1 Non-combustible Facing Diagram

0 in.

NON-COMBUSTIBLE

BOARD

COMBUSTIBLE MATERIAL

0 IN.

MODEL

in.

HEIR36

1549

57-5/8

1464

HEIR42

67 1702

62-5/8

1591

HEIR50

1905

66-5/8

1692

Содержание HEIR36





























































Результаты поиска

Содержание HEIR36

Отзывы:

Похожие инструкции для HEIR36

Бренды по названию

Популярные бренды

Heatilator HEIR36, Руководство по установке

Результаты поиска

Содержание HEIR36

Отзывы:

Похожие инструкции для HEIR36

Бренды по названию

Популярные бренды