Heatilator HEIR36 Скачать руководство пользователя | Manualshive

Страница: 47 / 60

background image

47

Heatilator • HEIR36, HEIR42, HEIR50 Installation Manual • 2285-980 Rev. G • 12/14

11

11

Appliance Setup

Figure 11.2. Glass Clip Tool Location

Figure 11.3. Inserting Glass Clip Tool

Figure 11.1. Glass Clip Tool

CAUTION! Risk of Cuts or Abrasions.

Wear protective

gloves and safety glasses during installation. Sheet metal
edges are sharp.

Removing Fixed Glass Assembly

This

fi

xed glass assembly is held in place by lower glass

clips, side clips and top retaining rail. To remove clips, en-
gage the spring clips with the tool and pull tool out slightly.
1. The glass clip removal/installation tool is fastened to

the lower right corner of the appliance. Remove tool
by removing one screw. See Figure 11.1. If glass clip
removal tool becomes misplaced, a cotter pin removal
tool may be used.

3. Disengage the left and right glass clips one at a time

using the glass clip removal/installation tool. Insert
tool from the top side of the side glass clip. Pull the
glass tool out slightly to disengage the side clip. See
Figure 11.7.

4. Grasp the left and right sides of the glass assembly

and carefully pull outward to remove the bottom from
the support tabs on the bottom glass clips. Lower the
glass to remove it from the top retainer rail.

NOTICE:

Protect and prevent the hearth from damage by

covering it with a drop cloth.

CAUTION! Risk of Injury! DO NOT

put

fi

ngers under

glass frame. Fingers may get pinched by glass frame
during removal.

A. Fixed Glass Assembly

WARNING! Risk of Asphyxiation!

Handle

fi

xed glass

assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.

•

DO NOT

strike, slam or scratch glass.

•

DO NOT

operate

fi

replace with glass removed, cracked,

broken or scratched.

•

Replace as a complete assembly.

WARNING! Risk of Injury!

Glass assembly installation

and removal must be performed by a quali

fi

ed service

technician. See chart below for glass assembly weights.

• HEIR42 AND HEIR50 MODELS: It is recommended

that Glass installation and removal be performed by
two quali

fi

ed service technicians.

2. To disengage bottom glass clips, position the glass

clip removal/installation tool parallel to the

fl

oor and

insert it about two inches into the gap between the
glass frame and the front bottom

fi

replace lip. Insert

the tool on the lower left side of the glass clip and
move to the right to engage the clip. Using one mo-
tion, pull out slightly while pushing down to disengage
bottom glass clip. Repeat for the other bottom spring
clips. There are three on the HEIR36 and four on the
HEIR42 and HEIR50. See Figure 11.3.

Glass Weights

HEIR36 HEIR42

HEIR50

32 lbs

41 lbs

54 lbs

«
...
45
46
47
48
49
...
»

Содержание HEIR36





























































Отзывы:

Нет отзывов

Похожие инструкции для HEIR36

Бренд: Harman Страницы: 10

Бренд: Majestic Страницы: 60

Бренд: Desa Страницы: 44

Бренд: Amantii Страницы: 21

Бренд: C3 Страницы: 2

Бренд: Valcourt Страницы: 12

Бренд: Napoleon Страницы: 112

CORINTHIA BLACK NG

Бренд: superior fires Страницы: 12

Бренд: Twin-Star International Страницы: 44

Бренд: La Hacienda Страницы: 4

Atraflam 16/9eme 600

Бренд: Atra Страницы: 24

Бренд: Paromax Страницы: 36

LANGSTON OFW821RC

Бренд: pleasant hearth Страницы: 24

Бренд: pleasant hearth Страницы: 15

Бренд: pleasant hearth Страницы: 4

Бренд: pleasant hearth Страницы: 33

Бренд: Hearth and Home Technologies Страницы: 32

Бренд: Hearth and Home Technologies Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды