Heatilator HEIR36 Скачать руководство пользователя

Страница: 35 / 60

Heatilator • HEIR36, HEIR42, HEIR50 Installation Manual • 2285-980 Rev. G • 12/14

Important Notice:

Heat shields may not be

eld constructed.

E. Horizontal Termination Requirements

Heat Shield Requirements for Horizontal

Termination

WARNING! Risk of Fire!

To prevent overheating and

re,

heat shields must extend through the entire wall thick-
ness.

•

DO NOT

remove the heat shields attached to the

wall shield

restop and the horizontal termination cap

(shown in Figure 7.13).

• Heat shields must overlap 1-1/2 in. (38 mm) mini-

mum.

There are two sections of the heat shield. One section
is factory-attached to the wall shield

restop. The other

section is factory-attached to the cap. See Figure 7.13.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm, the heat

shields on the cap and wall shield

restop must be

trimmed. A minimum 1-1/2 in. (38 mm) overlap MUST
be maintained.

• Use an extended heat shield if the

nished wall

thickness is greater than 7-1/4 in. (184 mm).

Figure 7.13 Venting through the wall

INTERIOR

HEAT SHIELD OR

EXTENDED

HEAT SHIELD

WALL SHIELD

FIRESTOP

HEAT SHIELD

1-1/2 IN. (38 MM) MIN.

OVERLAP

SHEATHING

VENT DEPTH FROM BACK OF APPLIANCE TO

OUTSIDE SURFACE OF EXTERIOR WALL

(SEE CHART BELOW)

SLIP SECTION

CAN BE EXTENDED

INNER VENT

OUTER VENT

EXTERIOR

Note:

When using termination caps with factory-supplied

heat shield attached, no additional wall shield

restop is

required on the exterior side of a combustible wall.

Install Horizontal Termination Cap

WARNING! Risk of Fire!

The telescoping

ue section of

the termination cap MUST be used when connecting vent.

• 1-1/2 (38 mm) minimum overlap of

ue telescoping

section is required.

Failure to maintain overlap may cause overheating and

re.

• Vent termination must not be recessed in the wall. Siding

may be brought to the edge of the cap base.

• Flash and seal as appropriate for siding material at

outside edges of cap.

• When installing a horizontal termination cap, follow

the cap location guidelines as prescribed by current

ANSI Z223.1

and

CAN/CGA-B149

installation codes

and refer to Section 4 of this manual.

CAUTION! Risk of Burns!

Local codes may require in-

stallation of a cap shield to prevent anything or anyone
from touching the hot cap.

NOTICE:

For certain exposures which require superior

resistance to wind-driven rain penetration, a

ashing kit

and HRC caps are available. When penetrating a brick
wall, a brick extension kit is available for framing the brick.

• The extended heat shield may need to be cut to length

maintaining suf

cient length for a 1-1/2 in. (38 mm)

overlap between heat shields.

• Attach the extended heat shield to either of the existing

heat shields using the screws supplied with the extended
heat shield. Refer to vent components diagrams in the
back of this manual.

• Rest the small leg on the extended heat shield on top

of the pipe section to properly space it from the pipe
section.

Install Vertical Termination Cap

• Attach the vertical termination cap by sliding the inner

collar of the cap into the inner

ue of the pipe section

while placing the outer collar of the cap over the outer

ue of the pipe section.

• Secure the cap by driving three self-tapping screws

(supplied) through the pilot holes in the outer collar of
the cap into the outer

ue of the pipe. See Figure 7.12.

Termination Cap

(1 of 3)

Storm

Collar

Caulk

Screws

Figure 7.12

Содержание HEIR36





























































Результаты поиска

Содержание HEIR36

Отзывы:

Похожие инструкции для HEIR36

Бренды по названию

Популярные бренды

Heatilator HEIR36, Руководство по установке

Результаты поиска

Содержание HEIR36

Отзывы:

Похожие инструкции для HEIR36

Бренды по названию

Популярные бренды