Heatilator HEIR36 Скачать руководство пользователя

Страница: 31 / 60

Heatilator • HEIR36, HEIR42, HEIR50 Installation Manual • 2285-980 Rev. G • 12/14

Figure 6.6 Shipping Location of Non-Combustible Board

C. Installing Non-Combustible Facing Material

WARNING! Risk of Fire!

• Follow these instructions exactly.
• Facing materials must be installed properly to prevent

re.

• No materials may be substituted without authorization

by Hearth & Home Technologies.

PERIMETER:

SECURE TO FRAMING WITH

DRYWALL SCREWS OR NAILS

(NOT INCLUDED)

INTERIOR:

SECURE WITH

SELF-TAPPING SCREWS

(IN MANUAL BAG ASSEMBLY)

Figure 6.7 Installing Non-Combustible Facing Material

• The

nishing templates are shipped fastened to the top

surround. Remove

nishing templates prior to installing

non-combustible board.

• Remove non-combustible facing pieces from back of

appliance. See Figure 6.6.

• Install non-combustible facing material to the appliance

using the screws supplied in the manual bag assembly.

• Center and attach two top boards to the framing

members. See Figure 6.7.

• Attach left and right side pieces to framing members.
• Use fasteners from fastener packet (in manual bag) for

screws that secure to the

replace. See Figure 6.7.

• Use regular sheetrock screws or nails to secure the

perimeter of the non-combustible facing materials to the
wood framing. See Figure 6.7.

• Use a wet or dry towel or soft brush to remove dust or

dirt from facing material.

• See Section 10 for

nishing materials guidelines.

Содержание HEIR36





























































Результаты поиска

Содержание HEIR36

Отзывы:

Похожие инструкции для HEIR36

Бренды по названию

Популярные бренды

Heatilator HEIR36, Руководство по установке

Результаты поиска

Содержание HEIR36

Отзывы:

Похожие инструкции для HEIR36

Бренды по названию

Популярные бренды