Heatilator HEIR36 Скачать руководство пользователя

Страница: 46 / 60

Heatilator • HEIR36, HEIR42, HEIR50 Installation Manual • 2285-980 Rev. G • 12/14

D. Decorative Front Dimensions for Finish-

ing

A decorative front is required for this appliance. Only dec-
orative fronts certi

ed for use with this appliance model

may be used. Contact your dealer for a list of decorative
fronts that may be used. Once you have determined what
kind of decorative front and

nishing material is going to

be used on the

replace, you may use the table below

which shows the decorative front models and the

nish-

ing material thickness allowed. For an inside

t there is an

available template to ensure that proper decorative front
clearances are maintained with

nishing material with

thickness greater than 1 inch.

COMBUSTIBLE MATERIAL

C (ARCH)

Figure 10.13 Inside Fit Decorative Fronts

The decorative fronts approved for use with this appli-
ance have been designed to be installed by two methods:
Overlap Fit or Inside Fit. Before beginning the installation,
it is important to determine with method will be used.

Overlap Fit Method:

These decorative fronts have been

designed to be installed over

nishing material up to one

inch thick.

Inside Fit Method:

These decorative fronts may be re-

cessed into non-combustible

nishing material up to 6

inches thick.

NOTICE:

Proper clearances from the

replace opening

to any

nishing material thicker than 1 inch MUST be

maintained.

NOTE:

Finishing templates are included with this product.

See Section 10.B.

Table 10.1. Approved Decorative Fronts

DIMENSIONS

3/4 IN.

1-1/4 IN.

FIRESCREEN DECORATIVE FRONTS

RECTANGULAR

ARCHED*

FS-36

FS-36A*

FS-42

FS-42A*

FS-50

FS-50A*

*Requires Arch Template Kit (not included)

Содержание HEIR36





























































Результаты поиска

Содержание HEIR36

Отзывы:

Похожие инструкции для HEIR36

Бренды по названию

Популярные бренды

Heatilator HEIR36, Руководство по установке

Результаты поиска

Содержание HEIR36

Отзывы:

Похожие инструкции для HEIR36

Бренды по названию

Популярные бренды