heat-timer SQ-Elite-EXt Скачать руководство пользователя страница 32

Страница: 32 / 44

Heat-Timer Corp.

stage settIngs

Button:

BOILER/

• In most installations, all active boiler adjustments are the same, but each can be configured

differently if desired.

• When the Boiler button is depressed, the first Boiler settings menu will be shown.

• Make all the appropriate settings for the first boiler (See below).

• Then select the

Next Boiler

option from the menu and make all the settings.

Continue until all boilers have been set.

• If a SQ-Elite-EXT is connected to the SQ-Elite-MV, scrolling through boilers using the

Next

and

Prev

Boiler

menu options will scroll through the extension boilers as well.

alert

To be able to change the SQ-Elite-MV settings, the Program/Run Switch must
be set to Program. The switch is located under the Enclosure Wiring Cover for
security. The Enclosure Wiring Cover can be securely closed using a padlock.

----- BOILER AB -----

Mode

Auto

Runtime

58Hrs

<Prev Boiler>

<Next Boiler>

BACK SAVE

PROGRAM

RUN

Mode

Auto, Standby, Off, On

Default: Auto

Button:

BOILER/Mode

• The SQ-Elite-MV only controls any boiler set to Auto or (after a delay) Standby. The On

and Off settings are not recommended for to active boilers.

• Any output without an active boiler must be set to Off.

• The following list describes the MODE options:

-- BOILER AB MODE -

Auto

Standby

Off

BACK SAVE

Auto

- The SQ-Elite-MV will control the boiler operation to maintain the desired Set Point. Only boilers set to Auto can be Lead.

Standby

Standby boilers can only be activated when all boilers in Auto have been at HI for an adjustable Standby delay period. A

boiler can be set to Standby if needed to be available in extreme load conditions. Note that a Standby boiler Cannot be a

Lead boiler. Standby Time is only available in PID mode.

Off

Any boiler output not connected to a physical boiler should be set to Off. The Off Mode can also be used to disable boilers

that are being serviced.

The On Mode should only be used when testing a boiler. The On Mode overrides the

PROVE and SHUTDOWN

inputs.

Once set to On the boiler will immediately start all of its stages as well as the SEQ System relay.

runtIMe

Clear

Button:

BOILER/RunTime

• The RunTime provides an accumulative hourly run for the selected boiler lowest stage.

• The RunTime for a specific boiler can be reset to zero by pressing the middle two buttons.

When doing so, record the date and time at which the reset took place for future reference.

BOILER AB RUNTIME

58hrs

BACK CLEAR OK

Содержание SQ-Elite-EXt













































Результаты поиска

Содержание SQ-Elite-EXt

Отзывы:

Похожие инструкции для SQ-Elite-EXt

Бренды по названию

Популярные бренды

heat-timer SQ-Elite-EXt, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SQ-Elite-EXt

Отзывы:

Похожие инструкции для SQ-Elite-EXt

Бренды по названию

Популярные бренды