heat-timer SQ-Elite-EXt Скачать руководство пользователя страница 21

Страница: 21 / 44

SQ-Elite-MV & SQ-Elite-EXT Installation Manual

MoV sensor fault

Valve Close, Valve Open

Default: Valve Close

Hold Button:

MENU/<System Startup>/..../MOV Sensor Fault

The MOV Sensor Fault will determine the operating status of the motorized valve when a
sensor reads Short or Open.

MOV SENSOR FAULT

Valve Close

Valve Open

BACK SAVE

reset Mode

• When Valve Close is selected, the SQ-Elite-MV will energize the MOV Close relay when the MOV System reads Short or Open.

However, when the Outdoor reads Short or Open, the SQ-Elite-MV will change the Target to the MOV Minimum Target.

• When Valve Open is selected, the SQ-Elite-MV will energize the MOV Open relay when the MOV System reads Short or Open

and the outdoor temperature is below MOV Outdoor Cutoff. However, if the outdoor temperature is above the Outdoor Cutoff, the

Outdoor Cutoff will take over turn off the stages. When the outdoor reads Short or Open, the SQ-Elite-MV will change the Target

to the MOV Maximum Target.

set poInt Mode

• If Valve Close is selected, the SQ-Elite-MV will energize the MOV Close relay when the SEQ System sensor reads Short or Open.

• If Valve Open is selected, the SQ-Elite-MV will energize the MOV Open relay when the MOV System sensor reads Short or Open.

• The Outdoor Sensor Short or Open status will not affect the control operation in Set Point mode.

settIng tHe control to factory defaults

To Reset the SQ-Elite-MV control to its original factory defaults, power down the control.

Hold down the two right most buttons while powering the control back up until the Total Clear

Started screen appears. The Display will direct you to the Startup menu after the defaults are

loaded to program the control.

NOTE: When resetting the control to original factory defaults all control settings will be over

written and will no longer exist.

alert

Do not turn off power to control until all Startup settings have been made.
Otherwise, the next power-up will be set to many Startup factory settings that

might not fit your application.

TOTAL CLEAR STARTED

Release buttons

and

Please Wait

Hold

durIng

power-up

Содержание SQ-Elite-EXt













































Результаты поиска

Содержание SQ-Elite-EXt

Отзывы:

Похожие инструкции для SQ-Elite-EXt

Бренды по названию

Популярные бренды

heat-timer SQ-Elite-EXt, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SQ-Elite-EXt

Отзывы:

Похожие инструкции для SQ-Elite-EXt

Бренды по названию

Популярные бренды