76
4000511390
E03.16 USA
/
GB
General data
Structural part inspection
MS0001
3.3 - FUNCTIONAL TESTS
The following tests must be carried out each 250 h or 6 months or afterwards :
• An important technical intervention.
• An accident resulting from a failure of a major component.
The following tests must be realized by a qualified staff under secure conditions.
The results of the tests must be entirely documented.
To avoid the swing of the machine during the test, it is imperative that a device of reserve (chain, not of anchoring) is
used during the test.
3.4 - DYNAMIC TESTS
The machine must be place on level and firm ground.
With 100% of the maximum allowed load, operate from ground control box (or emergency control box) all the
movements ; the platform floor must reach a height of about 1 above the ground.
The functional tests must show the following facts :
• The machine carried out all the movements without jolts while supporting the load.
• All the security device function correctly.
• Authorized maximum speeds of operation are not exceeded.
Refer to the user manual for the description of the safety device and technical characteristics to be reached.
3.5 - STRUCTURAL TEST (OVERLOAD)
The following test shows that the structure of the machine is in conformity with the safety requirements.
The machine must be place on level and firm ground.
With 100% of the maximum allowed load, operate from ground control box (or emergency control box) all the
movements ; the platform floor must reach a height of about 1 above the ground :
• Measure the distance between the ground and the basket (or of the platform).
• Leave the machine in static during 15 mnn.
• Measure the distance between the ground and the basket (or of the platform).
If the difference between two measurements does not exceed 4 cm (1.575 in) : the test is validated.
If the difference between two measurements exceeds 4 cm (1.575 in), to contact HAULOTTE Services® or to carry
out the additional tests described below.
MS0003 - § 3.2 Cylinder inspection.
Содержание HT21RT O
