Harris NXAMP3801HDI Скачать руководство пользователя страница 10

Страница: 10 / 76

Chapter 1

Introduction

175-100423-00

Specifications

This section describes the hardware and software specifications for NXAMP3801HDX/HDI.

System

Table 1-4

describes the general specifications for NXAMP3801HDX/HDI:

Table 1-4

General Specifications

Specifications

HDX

HDI



32 GB RAM





Dual-head DVI monitor interface





Four 10/100/1000Base-T Ethernet adapters





Four USB 2.0 ports on back panel





PCI Express platform





Single boot drive with optional second drive for RAID1





Two redundant 8 Gb Fibre Channel ports





Two Six-Core Intel Xeon 64-bit processors





Two USB 2.0 ports on front panel





USB keyboard and mouse (included)





Windows 7 Ultimate (64-bit)





Single boot drive with an option for a second drive for RAID 1





Software-based codecs for coding and decoding SD and HD media





Supports HD-SDI (SMPTE-292M) and AES/EBU interfaces





Supports NEXIO Farad shared storage with hundreds of terabytes of
usable shared storage with RAID-601 storage protection





Supports redundant Ethernet, which automatically switches operation
from one Ethernet network to the other, if one Ethernet network fails





Supports SD (525i, 625i) and HD (1080i, 1080p, 720p) content on the
same chassis





Supports up to 8 SD channels, or up to 4 HD channels





Two Six-Core Intel Xeon

64-bit processors





Works with a wide range of 3

party automation, archiving, and media

management applications



Table 1-3

Key Features (Continued)

Features

HDX

HDI

Содержание NXAMP3801HDI













































































Результаты поиска

Содержание NXAMP3801HDI

Отзывы:

Похожие инструкции для NXAMP3801HDI

Бренды по названию

Популярные бренды

Harris NXAMP3801HDI, Руководство по установке оборудования и инструкция пользователя

Результаты поиска

Содержание NXAMP3801HDI

Отзывы:

Похожие инструкции для NXAMP3801HDI

Бренды по названию

Популярные бренды