Harris NXAMP3801HDI Скачать руководство пользователя страница 65

Страница: 65 / 76

NXAMP3801HDX/HDI

NEXIO AMP Generation 6 Hardware Installation and User Guide

175-100423-00

Hard Drive Removal or Replacement

The NXAMP3801HDX/HDI comes equipped with hot-swappable hard drives. Only Harris qualified hard disk
drives are for use in NXAMP3801HDX/HDI chassis.

CAUTION

Regardless of how many hard drives are installed, all drive carriers must remain in the

drive bays to maintain airflow.

Removing a Hard Drive Carrier from the Chassis

Figure 8-6

Carrier release locations

Press the drive release button. See

Figure 8-6

Swing the handle out fully.

Pull the carrier straight out.

Installing a Hard Drive into a Drive Carrier

Remove the carrier from the NXAMP3801HDX/HDI. Refer to

Removing a Hard Drive Carrier from the

Chassis

on page 65.

Insert your new drive into the carrier with the PCB side facing down and the connector end toward
the rear of the carrier.

Align the drive in the carrier so that the mounting holes of both are aligned. Refer to

Figure 8-7

page 66.

Содержание NXAMP3801HDI













































































Результаты поиска

Содержание NXAMP3801HDI

Отзывы:

Похожие инструкции для NXAMP3801HDI

Бренды по названию

Популярные бренды

Harris NXAMP3801HDI, Руководство по установке оборудования и инструкция пользователя

Результаты поиска

Содержание NXAMP3801HDI

Отзывы:

Похожие инструкции для NXAMP3801HDI

Бренды по названию

Популярные бренды