Harris NXAMP3801HDI Скачать руководство пользователя страница 53

Страница: 53 / 76

How to Create or Rebuild a
RAID 1 Boot Drive

Your NEXIO AMP is shipped with only one boot drive. An optional boot drive can be ordered and set up as a
mirrored drive known as RAID 1.

Creating a New RAID 1 Boot Drive

The following procedures will step you through the process of turning a single boot disk into a 2 drive
RAID 1 boot volume. These procedures are to be done only when the Server is down for maintenance.

Make sure to backup all important data before creating a new RAID 1 drive.

Remove the Drive 1 carrier (

Removing a Hard Drive Carrier from the Chassis

on page 65) and

mount the spare SSD drive on the carrier. Refer to

Installing a Hard Drive into a Drive Carrier

page 65.

Re-insert the spare SSD drive and carrier into its bay vertically, keeping the carrier oriented so that the

release button is on the right side. When the carrier reaches the rear of the bay, the release handle
will retract.

Push the hard drive into the hard drive bay until the hard drive clicks into the locked position.

Locate the application through the Microsoft Windows start menu and select

Intel Raid Storage

enterprise.

Figure 7-1

Start menu

Содержание NXAMP3801HDI













































































Результаты поиска

Содержание NXAMP3801HDI

Отзывы:

Похожие инструкции для NXAMP3801HDI

Бренды по названию

Популярные бренды

Harris NXAMP3801HDI, Руководство по установке оборудования и инструкция пользователя

Результаты поиска

Содержание NXAMP3801HDI

Отзывы:

Похожие инструкции для NXAMP3801HDI

Бренды по названию

Популярные бренды