Harris NXAMP3801HDI Скачать руководство пользователя страница 32

Страница: 32 / 76

Chapter 3

System Installation

175-100423-00

Choosing a Setup Location

•

Leave enough clearance in front of the rack to enable you to open the front door completely (~25
inches).

•

Leave approximately 30 inches of clearance in the back of the rack to allow for sufficient airflow
and ease in servicing.

•

This product is for installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).

Warnings and Precautions

Rack Precautions

•

Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the
full weight of the rack resting on them.

•

In single rack installations, stabilizers should be attached to the rack.

•

In multiple rack installations, the racks should be coupled together.

•

Always make sure that the rack is stable before extending a component from the rack.

•

You should extend only one component at a time. Extending two or more simultaneously may
cause the rack to become unstable.

General System Precautions

•

Review the electrical and general safety precautions that came with the components you are
adding to your chassis.

•

Determine the placement of each component in the rack before you install the rails.

•

Install the heaviest system components on the bottom of the rack first, and then work upwards.

•

Harris suggests that you use regulating uninterruptible power supplies (UPS) to protect the
NXAMP3801HDX/HDI from power surges, voltage spikes and to keep your system operating in
case of a power failure.

Mounting brackets



Nut plates



Rails



Short extensions



Slides



Serial Port Cable:

RJ-12 to DB9 male



RJ-12 to DB9 male slave



RJ-12 to DB9 tributary female connector



RJ-12 to RJ-12 cables



Weidm

ller B2L 3.50/16/180F



Table 3-1

Harris supplied Products (Continued)

Harris Supplied

Quantity

HDX

HDI

Содержание NXAMP3801HDI













































































Результаты поиска

Содержание NXAMP3801HDI

Отзывы:

Похожие инструкции для NXAMP3801HDI

Бренды по названию

Популярные бренды

Harris NXAMP3801HDI, Руководство по установке оборудования и инструкция пользователя

Результаты поиска

Содержание NXAMP3801HDI

Отзывы:

Похожие инструкции для NXAMP3801HDI

Бренды по названию

Популярные бренды