Harris NetWave Скачать руководство пользователя страница 61

Страница: 61 / 90

Revision A • 6/06

4-1

his chapter covers setup, configuration and

use of linked NetWave consoles within VistaMax

audio management systems. Two Monitor panel

labels (

VistaMax Enabled and VistaMax Linked)

light up when the NetWave is properly linked

with a VistaMax system. If the two labels are not

lit, the information in this chapter does not apply

to that NetWave since it is not a linked console.

Linked NetWave Consoles

The first step to link a NetWave console to a

VistaMax system is to install the optional Link

Activation Kit (99-1425). After installation, the

Monitor panel’s

VistaMax Enabled label lights

to indicate the kit was properly installed.

The second step is to physically link the Net-

Wave to a VistaMax or Envoy card frame. This

card frame becomes the NetWave’s

parent de-

vice

, which means it controls the routing of

linked signals to/from the console. The console’s

rear panel Link jack connects to any available

Hub card facet using a CAT-5e or CAT-6 cross-

over cable. Cable runs up to 300 feet [100M]

are supported. Once connected, a second Moni-

tor panel label,

VistaMax Linked, lights to indi-

cate a good connection has been established.

With both labels lit, the third step is to con-

figure the NetWave’s parent device to add the

NetWave, and any Dual Router panels that were

added, to the VistaMax system. To do this the

VistaMax system must be running 500-series

(501.50 or later) operating system code; the Vis-

taMax Control Center (VMCC) setup software

must be build 2065 (or later); and Community

Monitor (CM) must be version 3.55 or later.

If the VistaMax system is new, all of these

should be correct, but when the NetWave is be-

ing added to an existing VistaMax system, the

system devices may be running older software.

The current versions for each of these programs

(as of the ship date of the console) was supplied

with the console on the 99-5001 NetWave CD-

ROM. Even newer versions of each program

may be available on the Harris PR&E FTP site

(ftp.pre.com). See the Service chapter (page 5-

1) for information about logging into this site.

VERIFYING SOFTWARE VERSIONS

To verify the version of software running on

each VistaMax system device, run Community

Monitor, select menu item

View then Status. The

Vers

column lists which version of code is run-

ning on each device in the system.

VistaMax devices running 400-series code

(445.10 was the last 400-series code released)

must be updated to the 500-series code in order

to integrate NetWave consoles and Envoy card

frames into a VistaMax system. The customer

doc

71-2002_500-series_code_update.pdf

, which

is also included on the 99-5001 CD-ROM, has a

detailed procedure for updating the operating

system code.

NetWave

Linking

Содержание NetWave



























































































Результаты поиска

Содержание NetWave

Отзывы:

Похожие инструкции для NetWave

Бренды по названию

Популярные бренды

Harris NetWave, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание NetWave

Отзывы:

Похожие инструкции для NetWave

Бренды по названию

Популярные бренды