Harris NetWave Скачать руководство пользователя страница 17

Страница: 17 / 90

Revision A • 6/06

A T

2-1

Installation

he NetWave console sits on the countertop

on four rubber feet. One cable access cutout is re-

quired under the frame for cabinet wiring to cleanly

connect to the console connectors. These are hid-

den under a cosmetic cover after installation. For

security and stability, the console should be fastened

to the countertop using two #8 or #10 screws or

bolts (not supplied). Two .256" chassis holes be-

hind the front two feet are provided for this. Frame

sizes and cutout dimensions are listed below.

The NetWave console shipment contains:

• NetWave main frame, loaded with DSP & I/O

and Monitor & Output cards; a Monitor panel;

Dual Fader panels (NetWave-8 has four; Net-

Wave-16 has six plus two dual blanks; NetWave-

24 has nine plus three dual blanks); optional

items ordered (additional Dual Fader panels, Vis-

taMax Link Activation Kit, Dual Router Kits,

Quad Meter Package)

• 48-volt DC power supply (50-27 in-line supply

or a 99-1205 rackmount supply and DC cable)

• Installation kit (MOD IV housings and recep-

tacle contacts, blank source name labels)

• Channel Setup Stylus Tool

• Reflector for the Console Display

• NetWave Quick Guide

• NetWave CD-ROM

Dimension Table

Frame Size

Width Cable Access Dims.

NetWave-8

20" [508]

x 17" [51 x 432]

NetWave-16

32.8" [833]

x 30" [51 x 762]

NetWave-24

45.6" [1158]

x 43" [51 x 1092]

NetWave consoles are 21" [534] deep (from the front of the palm rest
to the back tips of the side panels). Add .5" [13] additional clear-
ance behind the console in order to fully open the connector cover
when the console’s rear is against a wall.

The console height above the countertop is 3" [76], except for the con-
sole display reflector, which is 8" [203] above the countertop.

Typical console setback from the countertop edge to the palm rest is be-
tween 6" [152] and 12" [305].

Millimeter dimensions listed in brackets. All dimensional tolerances are:

¼" [6.4].

12345678901234567890123

CABLE ACCESS OPENING

Setback

(typ. 6" - 12")

18.5"

COUNTERTOP EDGE

Cable Access Cutout & Console Mounting holes

.256" holes to fasten

console to countertop

See Dimension Table for Width

NetWave-8 console with Dual Fader and

Monitor Control panels removed

21"

Содержание NetWave



























































































Результаты поиска

Содержание NetWave

Отзывы:

Похожие инструкции для NetWave

Бренды по названию

Популярные бренды

Harris NetWave, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание NetWave

Отзывы:

Похожие инструкции для NetWave

Бренды по названию

Популярные бренды