Harman Studer Vista FX Скачать руководство пользователя

Страница: 46 / 56

Vista FX

1-30 Vista FX

Document generated: 28.08.14

SW V4.9

Voice 1 Frequency :

The delay voice output signal is filtered by a one pole low-pass. This is the

filters cutoff frequency Range [50 .. 20’000] Hz

Voice 1 FB :

The feedback signal is filtered by a one pole low-pass. This is the filters cutoff

frequency Range [50 .. 20’000] Hz

Mst Diffusion :

Input diffusion is the first part of processing for any signal entering a delay.

It can be described as a smearing or softening of the signal and is typically

used to lessen the impact of strong transients. Range [0 .. 100] %.

FB Diffusion :

Feedback Diffusion is similar to Input Diffusion, except that it is applied to

a delayed signal that is being added back into the input. Range [0 .. 100] %.

LFO Rate :

Sets the speed of an LFO. Range [0.01 .. 10.0] Hz

Delay Feedback :

Controls all delays in the algorithm. Each voice has its nominal feedback gain

adjusted by this percentage. Range [0 .. 100] %.

Tapping :

Assigns the Tap control to one of the

USR

buttons on the consoles channel

strip. Range [No, USR1, USR2]

Содержание Studer Vista FX

























































Результаты поиска

Содержание Studer Vista FX

Отзывы:

Похожие инструкции для Studer Vista FX

Бренды по названию

Популярные бренды

Harman Studer Vista FX, Руководство по эксплуатации

Результаты поиска

Содержание Studer Vista FX

Отзывы:

Похожие инструкции для Studer Vista FX

Бренды по названию

Популярные бренды