Harman Studer Vista FX Скачать руководство пользователя

Страница: 3 / 56

For Your Own Safety and to Avoid Invalidation of the Warranty

Please Read This Section Carefully

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with a dry cloth.

• Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

• Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

• Do not defeat the safety purpose of a polarised or grounding type plug. A

polarised plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or

the third prong are provided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for replacement of the obsolete

outlet

• Protect the power cord from being walked on or pinched particularly

at plugs, convenience receptacles and the point where they exit from the

apparatus.

• Only use attachments/accessories specified by the manufacturer.

• Use only with the cart, stand, tripod, bracket or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use cau

tion when moving the cart/apparatus combination to avoid injury from

tip-over.

• Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way, such as the power

supply cord or plug is damaged, liquid has been spilled or objects fallen

into the apparatus, the apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

Note: It is recommended that all maintenance and service on the product

should be carried out by Studer or its authorised agents. Studer cannot

accept any liability whatsoever for any loss or damage caused by service,

maintenance or repair by unauthorised personnel.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus

to rain or moisture. Do not expose the apparatus to dripping or splashing

and do not place objects filled with liquids, such as vases, on the appara

tus.

• No naked flame sources, such as lighted candles, should be placed on the

apparatus.

• Ventilation should not be impeded by covering the ventilation openings

with items such as newspapers, table cloths, curtains etc.

WARNING: Do not use this apparatus in very dusty atmospheres, or in atmospheres

containing flammable gases or chemicals.

• THIS APPARATUS MUST BE EARTHED. Under no circumstances

should the safety earth be disconnected from the mains lead.

• The mains supply disconnect device is the mains plug. It must remain

accessible so as to be readily operable when the apparatus is in use.

• If any part of the mains cord set is damaged, the complete cord set should

be replaced. The following information is for reference only. The wires

in the mains lead are coloured in accordance with the following code:

Safety Information

Содержание Studer Vista FX

























































Результаты поиска

Содержание Studer Vista FX

Отзывы:

Похожие инструкции для Studer Vista FX

Бренды по названию

Популярные бренды

Harman Studer Vista FX, Руководство по эксплуатации

Результаты поиска

Содержание Studer Vista FX

Отзывы:

Похожие инструкции для Studer Vista FX

Бренды по названию

Популярные бренды