Harman Studer Vista FX Скачать руководство пользователя

Страница: 24 / 56

Vista FX

1-8 Vista FX

Document generated: 28.08.14

SW V4.9

Node=555

this ID must be different on the redundant PC

DhcpEnabled=No

must be set to “No”

IpAddress=192.168.3.128

this needs to be the used subnet

ReconfigureDeviceInDiffSubnet=Yes

must be set to “Yes”

; old entries for compatibility

SubnetMask=255.255.255.0

must be set to exact this value

Gateway=0.0.0.0

must be set to exact this value

SerialNumber=001B214F13C6

must be set to exact this value

Male sure an “s” is added to the relevant DSP card serial port. e.g. if the Vista

FX unit is connected to the DSP card in slot 4, the following entry is neces-

sary :

[d950SerialPorts]

10= {

} TCP4 slot=4

must be set to “s”

The following enrties define the DSP card slot number and HD-Link port

number where the Vista FX units are connected to. The default entries are

empty, allowing automatic discovery via D21m. These settings can also be

used to configure Vista FX units being connected to the second HD-Link (port

1) of a DSP card, where no D21m communication can be used and therefore

Vista FX units cannot be detected automatically. For Offline usage of Vista

FX with e.g. a Virtual Vista where no Vista FX units have been connected

before, manually entered numbers will enable to Vista SW to emulate the FX

units.

[LexiconFX]

ConnectedDspCardSlot=

empty or 1-9

ConnectedDspCardPort=

empty or 0-1

3.4 Files on the redundant Vista control pc

On the redundant PC there must be an additional set of the two

FXConfigu-

ration.xml

and

FXConfiguration.xdr

files in the D950System

folder.

If both PCs share the same HiQNet subnet, then the files can be identically.

This is the recommended setting for the redundant PC setup.

Make sure that the HiQNet node ID (555 is default) of the redundant PC is

different o the main PC.

3.5 setup process in Vista application

Setup Dialog in the Vista application : Once all the above is done correctly, the Vista application can be started and

the “FX Audio Setup Dialog“ can be run. This dialog is found in the System

Administrator menu.

Содержание Studer Vista FX

























































Результаты поиска

Содержание Studer Vista FX

Отзывы:

Похожие инструкции для Studer Vista FX

Бренды по названию

Популярные бренды

Harman Studer Vista FX, Руководство по эксплуатации

Результаты поиска

Содержание Studer Vista FX

Отзывы:

Похожие инструкции для Studer Vista FX

Бренды по названию

Популярные бренды