Harman Kardon System 13828, Руководство пользователя

Страница: 5 / 50

REMOTE CONTROL FUNCTIONS 5
Remote Control Functions, common for AVR 138 and DVD 28
IMPORTANT NOTE: The 13828 remote has
some buttons that perform different functions. If
you press the
AVR Button , one set of func-
tions is active, identical to the functions for but-
tons CD, Tape, Video 1/2/3. If you press the
DVD
Button
5
, some of the buttons change their
function as indicated above the button itself, and
explained below. Refer to the function table for
an overview of functions in both modes.
0
Power On Button: Press this button to
turn on the power to the AVR or the DVD selected
by pressing either the AVR or the
DVD Button
or
5
.
1
This indicator is not active.
2
IR Transmitter Window: Point this window
towards the AVR when pressing buttons on the
remote to make certain that infrared commands
are properly received.
3
Power Off Button: Press this button to
place the AVR or a selected device unit in the
Standby mode. If held for more than 3 seconds,
both the AVR and the DVD switch to Standby.
4
Mute: Press this button to momentarily
silence the AVR or TV set being controlled,
depending on which device has been selected.
5
Input Selectors: Pressing one of these
buttons will perform three actions at the same
time. First, if the AVR is not turned on, this will
power up the unit. Next, it will select the source
shown on the button as the input to the AVR.
Finally, the DVD Button will switch the double-
function remote buttons to their DVD functions.
After pressing the DVD Button, you must press
the
AVR Selector button again to operate
all the AVR’s functions with the remote. Note
that pressing the DVD Button switches on BOTH
the AVR and the DVD, whereas pressing the AVR
Button just switches on the AVR.
6
Info (DVD): Press for detailed informations
on the disc playing (Video/Audio Bit rate, Movie
aspect ratio and others), and for current player
settings made. Note that the unit doesn’t react
on any transport button as long as the info
menu is displayed. Press again to remove
information from screen.
7
Volume Up/Down: Press these buttons to
raise or lower the system volume.
8
HD Mode Selector (DVD): When the
DVD player is connected to a video display using
the
HDMI Output , the display sends infor-
mation to the DVD indicating the highest video
resolution it is capable of handling, and the
DVD automatically sets the video output to
match it. Pressing this button allows you to
manually change the output resolution, with
your selection indicated by the
Video Output
Indicators
O
.
The DVD will not allow you to select a resolution
beyond the capabilities of your display, and if
you try to do so, an on-screen error message will
appear to alert you to the selection of an incom-
patible video format. Changes made with this
button remain active until the DVD or the dis-
play is turned off. When either is turned off, and
then on again, the DVD will revert to the default
setting transmitted by the display.
9
Speaker Select/Setup: Press this button
to begin the process of configuring the AVR’s
Bass Management System for use with the type
of speakers used in your system. Once the but-
ton has been pressed, use the
K
/
L
buttons
to select the channel you wish to set up.
Press the OK button
A
and then select the
speaker type (see page 14 for more informa-
tion.)
For DVD: Press this button to use the DVD’s on-
screen menu system to adjust the player’s con-
figuration settings. Note that the
Info Button
6
must be pressed to access the DVD’s
Information menu to obtain detailed disc infor-
mation, and to configure the playback mode of
the disc.
A
OK Button: This button is used to enter
settings into the AVR’s memory. It is also used in
the setup procedures for delay time, speaker
configuration and channel output level
adjustment.
B
Delay/Status Button: Press this button to
begin the process for setting the delay times
used by the AVR when processing surround
sound. After pressing this button, the delay
times are entered by pressing the
OK button
A
and then using the
K / L
buttons to
change the setting. Press the Set button again to
complete the process. (See page 16 for more
information.)
For DVD: Press while a disc is playing to view
banner display. Use the ARROW buttons to move
through the different features in the Banner
Display. When a symbol is highlighted, press OK
on the remote to select it.
C
Memory/Angle Button: Press this button
to enter a radio station into the AVR’s preset
memory. Two underline indicators will flash at the
right side of the
Main Information Display
F
, you then have five seconds to enter a preset
memory location using the Numeric Keys .
(See page 23 for more information.)
For DVD: Press to access various camera angles
on a DVD (If the DVD contains multiple camera
angles) or to rotate JPEG images.
D
Clear Button: Press this button to clear
incorrect entries when using the remote to
directly enter a radio station’s frequency.
E
Preset Up/Down: When the tuner is in
use, press these buttons to scroll through the
stations programmed into the AVR’s memory.
When CD or DVD is selected using the
Input
Selector button
5
, these buttons may func-
tion as Slow Fwd/Rev (DVD) or ”+10” (CD).
F
RDS Select/Progressive Scan/Interlaced
Button: Press this button to display the various
messages that are part of the RDS data system of
the AVR’s tuner. (See page 24 for more informa-
tion on RDS).
For DVD: Press this button to change the resolu-
tion of the Component Video Output between
standard definition and progressive definition
(PAL interlaced and PAL progressive; NTSC inter-
laced and NTSC progressive).
The new setting will become effective after
quitting the Setup menu.
G
Playlist (DVD): Press this button to
change the playback order of the disc.
H
A-B (DVD): Press to select section A-B and
to play repeatedly.
I
DTS Neo:6 Mode Selector: Pressing this
selector button cycles the AVR through the
various DTS Neo:6 modes, which extract a five-
channel surround field from two-channel
program material (from PCM source or analog
input signal). The first press selects the last DTS
Neo:6 surround mode that was in use, and each
subsequent press selects the next mode in the
following order:
DTS Neo:6 MUSIC
DTS Neo:6
CINEMA
38277_AVR138_DVD28_ENG 23/07/08 18:36 Side 5